for Sonstige-Citroen XM
505 Articles | Page 8 of 11
Multimeter digital. Dimension: 74x145x40mm. Measuring range: Volt direct current + alternating
current. Ampere, resistance, continuity tester. Everything what you need, for car electrical connection.
O-Ring Assortment, 386 pcs. 32 sizes R-01 - R-32, inner-ø 3-44 mm, oil-, petrol- and
acid-resistant. Made in Germany.
Oil drain screw without magnet (interior square 8x8). Thread: M16 x 1,5. Suitable for Peugeot 204
304, 404, 504, 604, 505, J5, J7, J9. Renault. Citroen CX, BX, ZX, C15. Or. No. 0163.93
Gasket for oil drain plug for 2CV6, BX, XM, 204, 203, 304, 404, 504. inlet + exhaust screw
measure: 16,3x22x2mm. Version C, curved with a seal inside. (PTFE)
Oil draining pump 12 Volt. Ideal for emptying the hydraulic tank. For example Citroen DS, CX, GS
etc.. Of course other huiles oils can also be pumped with it. Super practical.
Oil absorbent pad. Extremely absorbent. Dimension: 51x38cm. For oils and brake fluids. Attention
the pads do not suck and absorb water! Your wife will be grateful!
Oil filter LS867B Peugeot + Citroen Diesel. Peugeot 504 XN2, 504 D, 205 D. Citroen CX D, Bx D
engines: TU/TUD/XU/XUD. Height: 79mm. Outside diameter: 76mm. Thread: M20x1,5. Or. No. 1109.N2
VIDEO P 504V6/R30, camshafts shaft seal (left-hand rotation). Suitable for Peugeot 504 V6, 604 V6
Renault R30 V6, Citroen XM. Dimension: 32 x 45 x 8mm.
Positive cable (battery to starter motor). Overall length: 500mm. Cable diameter: 16mm². Made in
the European Union. Universal fitting.
Upholstery Cleaner, Deep cleaning foaming action, 500ml. Eliminates tough stains and soils like
oil, grease and tar spots.
Wheel Stud Restorer Kit. For repairing damaged wheel stud threads using a reverse action to ensure
the alignment of the thread. Includes adaptor sizes: M12 x 1.25mm. M12 x 1.5mm. M14 x 1.5mm.
The brake-down aid for on the road. SONAX TyreFix restores driveability to flat tyres, without tyre
change. Seals small holes in the tyre and pumps it up. Practical, fast and safe. 400ml
Rust eraser pen. Ideal for removing even the smallest rust spots. Indispensable! And, of course
the cleaned rust spot must then be preserved with paint immediately.
Discs (windscreen) Pull-in tool (cord with handle). This is used to pull the rubber lip of the seal
over the sheet metal fold. Very helpful!
Windscreens (windscreen) piping assembly tool - bracket inserts. For small piping. There are 5
brackets in different widths so that narrow and wide piping can be fitted (e.g. for the 2CV, R4....). Suitable for tool with item number 20134.
Windscreen Installation Tool Set. Windshield sealing trim assembly tool. With this tools will the
rubber lip (seal) inclination (spread) and it can fit the sealing trim at the same time. Attention: The tool is for very wide piping. For chrome piping e.g. Citroen 2CV, Renault R4 etc. small brackets must be fitted. See our item number 20137.
Universal protective rubber (e.g. for protecting electric cables, brake lines, brake hoses
handbrake cables, speedometer cables, petrol hose... External dimensions: 23x30mm. Inner diameter: 8mm. The rubber is slit on one long side, and can therefore be easily placed over the cable to be protected!
Universal protective rubber (e.g. for protecting electric cables, handbrake cables, petrol hose
External dimension: 42mm. Length: 31mm. Inner diameter: 12mm. The rubber is not slit (but of course this can be done afterwards if it makes assembly easier)
Tube bending sleeve. Suitable for hose outer diameter of 12,5 > 13,4mm. Length: 60mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Tube bending sleeve. Suitable for hose outer diameter of 14,6 > 16,4mm. Length: 65mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Tube bending sleeve. Suitable for hose outer diameter of 16,5 > 18,4mm. Length: 70mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Tube bending sleeve. Suitable for hose outer diameter of 18,8 > 21mm. Length: 75mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Tube bending sleeve. Suitable for hose outer diameter of 21,8 > 24mm. Length: 90mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Hose clamp 11-17mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
505 Articles | Page 8 of 11
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
