for Citroën DS
3324 Articles | Page 38 of 67
Clutch cable reversing lever set, for clutch cable with approx. 596,5mm length. Only suitable for
Citroen DS IE (injection). Consisting of: lever, spring, bearing.
Clutch cable reversing lever set, for clutch cable with approx. 605,0mm length. Only suitable for
Citroen DS with carburetor engines. Consisting of: lever, spring, bearing. Or. No. DV31433A.
Clutch cable reversing lever, for clutch cable with about 596,5mm length. Only suitable for Citroen
DS IE (injection engine). Or.Nr.1D5438342N + DX31433
Clutch cable reversing lever, for clutch cable with about 605,0mm length. Only suitable for Citroen
DS with carburetor engines. Or. No. DV31433A. Made in Germany.
Clutch cable, suitable for Citroen DS 21 IE., starting from year of construction 1970. Length
570mm. Casing: 400mm. Or. No. DJ3142A
Clutch cable, suitable for Citroen DS DJ, starting from year of construction 1966. Length: 590mm
Casing covering: 380mm. Or. No. DV3142D
Clutch cable, suitable for Citroen DS IE, starting from year of construction 1972. (Diaphragm
clutch). Length: 610mm. Casing covering: 410mm. Or. No. 5404244 + 5404245
Clutch cable, suitable for Citroen DS, of year of construction 1965 to 1968. (3 lever finger
clutch). Length: 570mm. Casing covering: 425mm. Or. No. DM3142F
Clutch cable, suitable for Citroen DS, of year of construction 9/1962 to 8/1965. (3 lever finger
clutch). Length: 580mm. Or. No. DM3142D
Crank case (engine block) air vent hose above. Connection to the air intake hose between carburetor
air filter. Suitable for Citroen DS with carburetor engine. Inside diameter: 15 + 17mm. Or. No. 5413610M.
Crank case (engine block) air vent hose down. Suitable for Citroen DS IE (injection engine)
Dimension: 19.5 x 314mm. Or.Nr.DX132279A.
Crank case (engine block) air vent hose down. Suitable for Citroen DS, to year of construction
07/1972 (carburetor engine). Diameter: Both sides 19-20mm. Length: 230mm (shorten if necessary). Or. No. DX13276C, DY13276A, DX132-76A
Seal under the crankcase ventilation on the engine block (flat ring rubber). Suitable for Citroen
DS. Or. 5412031, ca. 78x87x2,4mm. Made in Germany.
Crankshaft bearing (complete set). Suitable for Citroen DS 19, to year of construction 1965
Citroen HY petrol. Reproduction. Dimension: 0.25 undersize.
Crankshaft bearing (complete set). Suitable for Citroen DS 19, to year of construction 1965
Citroen HY petrol. Reproduction. Dimension: 0.50 undersize.
Crankshaft bearing (complete set). Suitable for Citroen DS 19, to year of construction 1965
Citroen HY petrol. Reproduction. Dimension: 0.75 undersize.
Crankshaft bearing (complete set). Suitable for Citroen DS 19, to year of construction 1965
Citroen HY petrol. Reproduction. Dimension: 1,00 undersize.
Crankshaft bearing (complete set). Suitable for Citroen DS 19, to year of construction 1965
Citroen HY petrol. Reproduction. Dimension: Standard dimension. 54mm.
Crankshaft bearing (complete set). Suitable for Citroen DS, starting from year of construction 1965
(all engines). Reproduction. Dimension: 0.25 undersize (63,75mm).
Crankshaft bearing (complete set). Suitable for Citroen DS, starting from year of construction 1965
(all engines). Reproduction. Dimension: 0.50 undersize (63,5mm). Or. No. DX121-019B.
Crankshaft bearing (complete set). Suitable for Citroen DS, starting from year of construction 1965
(all engines). Reproduction. Dimension: Standard dimension. (64,00mm).
Bearing from synthetic (inside diameter 19,5mm. Outside diameter 26,0mm) for the gear change
intermediate spindle (connecting tube DJ334-102). Or. No. of the bearing: DJ334-140
Longitudinal chassis beam in front on the left. Lower sheet metal with the arc upward (end point in
front on the left, down). Suitable for Citroen DS, starting from year of construction 1967 (new front).
Longitudinal chassis beam in front on the left. Lower sheet metal with the curve upwards (end point
front left, below). Fits Citroen DS, up to year of manufacture 1967 (old front).
Longitudinal chassis beam in front on the right. Lower sheet metal with the arc upward (end point
in front on the left, down). Suitable for Citroen DS, starting from year of construction 1967 (new front).
Longitudinal chassis beam in front on the right. Lower sheet metal with the curve upwards (end
point front left, below). Fits Citroen DS, up to year of manufacture 1967 (old front).
Liner sealing ring down. Suitable for Citroen 11CV, 15CV, ID19, HY. Standard measurement of 0,07mm
Inside diameter: 83,5mm. Outside diameter 95mm. Or. No.: D1113A
Liners sealing ring down (4 fittings). Suitable for Citroen DS 23. Bore 93,5mm. Dimension
108x99x0,2mm. Or.Nr. DS111-3
Liners sealing ring down, suitable for Citroen DS 19/20/21. starting from year of construction
9/1968. 107x98,5x0,2 mm measured. Bore 90,0mm. Per piece! Or. No. DX1113
Idle stabilization completely, in the exchange. Idle stabilization does not have a vent screw
Suitable for Citroen DS IE (injection engine). Or. No. DXN142-020. Plus Old part deposit 150 Euro.
Idle stabilization completely, in the exchange. Idle stabilization does not have a vent screw
Suitable for Citroen DS carburetor. Or. No. Dx142-020. Plus Old part deposit 150 Euro.
Steering gear for Citroen DS, in the exchange. Suitable for hydraulic system LHM (power steering)
The steering unit is built up with newest seals and can be used for LHM liquid! Or. No. 9D5409726V. Plus 400 Euro Old part deposit. Note: The steering unit must be installed after the Citroen workshop specifications (workshop book 583, book 2, workingpaper D.444-1). You must have the tool 39002 (for the angle position of the steering gear to the steering column). Without this tool, you can not work!
Steering gear for Citroen DS, in the exchange. Suitable for hydraulic system LHS (power steering)
The steering unit is built up with newest seals and can be used for LHS liquid! Plus 400 Euro Old part deposit. Note: The steering unit must be installed after the Citroen workshop specifications (workshop book 583, book 2, workingpaper D.444-1). You must have the tool 39002 (for the angle position of the steering gear to the steering column). Without this tool, you can not work!
Steering gear repair set. Suitable for hydraulic systems LHM. Suitable for Citroen DS, starting
from year of construction 07/1967
Steering gear: Pressure spring for the damping pushrod of the steering rack. Diameter: 16.5mm. Or
No. D442-2 + 5411166. Suitable for Citroen DS.
Steering wheel + steering column trim, polished aluminium. Suitable for Citroen DS manual shift
car, built up to 10/1968.
Steering wheel + steering column trim, polished aluminium. Suitable for Citroen DS manual shift
car, built from 1962 to 09/1968. Or. No. DM822-63
Steering wheel + steering column trim, made of polished stainless steel. Suitable for Citroen DS
semi-automatic transmission, installed from year of construction 10/1968.
Steering wheel + steering columns cover, from polished stainless steel. Suitable for Citroen DS
semi-automatic transmission, Installed of year of construction 1962 to 09/1968. Or. No. DS822-63F
Steering wheel emblem (plaque), for the foamed steering wheel. Suitable for Citroen DS, starting
from year of construction 1970. Or. No. 1D 5410646U
Steering wheel foamed, completely with steering column. In the exchange. Suitable for Citroen DS
final version. Or. No. DX441202A. Plus 250 Euro Old part deposit.
3324 Articles | Page 38 of 67
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
