for Citroën 2CV 204-304

Bulb base (plug) for headlamp. Double-filament bulb + H4. Suitable for Citroen 2CV, HY, DS, Renault

R4, Peugeot 403, 404, etc.

lamp base Ba15s, 6 + 12 Volt, single-pole

• Suitable for this article
• 
  ball bulb 5 Watt 6 Volt base Ba15s / rear light, license plate light
  1,58 €
• 
  Ball lamp 6volt, 10watt. BA15S
  1,65 €

lamp base Ba7s, 6 + 12 Volt, single-pole

• Suitable for this article
• 
  Bulb 6 V, 1,2 Watt. Base Ba7S. For the large control light by older 2CV + HY
  1,83 €
• 
  Light bulb 12V, 2 Watt for pilot lamp (articles 50056-50059 ), socket BA7's
  1,19 €

Graphitic oil, lock oil. Optimally to clean and lubricate locks (door lock, starter lock etc.)

50ml.

Priming, penetrable, for sheet metal parts. 400ml

• Suitable for this article
• 
  Handhold for lacquer aerosol spray. Facilitates exactly and controlled alloting
  11,81 €

Rubber silent block M10. Diameter: 40mm. Overall height: 28mm. Suitable for Renault R16 and many

different.

• Suitable for this article
• 
  Nut M10, galvanized
  0,38 €

Silent block M8. Diameter: 40mm. Overall height: about 28mm. Thread: M8

• Suitable for this article
• 
  M8, nut for 12mm wrenche. (Metal) (e.g. carburetor on intake manifold 2CV).
  0,75 €

Exhaust silent rubber. Thread: M8. Dimension: 50 x 35 x 23mm. Suitable for Peugeot 304, 305, 504

505, 604. Or. No. 3062.06

Rubber mounting for the couple rod. Suitable for Peugeot 304, 504, 505, 604. Simca

1307/1308/Horizon. dimension: Inside diameter 10mm. Outside diameter 30mm diameter. Height of 20mm. Or. No. 5181.06 + 5093.03

Rubber cap for the connection to the starter motor. (Protecting cap). This cap should never be

missing. Universal fitting! For max. cable diameters: 17,8mm. Inside diameter 22mm.

Rubber cap for the connection at the generator. (Protecting cap). This cap should never be missing

Universal fitting! For max. cable diameters: 7,62mm. Inside diameter 12,7mm.

Rubber buffers for securing the bumper. This rubber has been used for many years on almost all

classic Peugeot models. Or. No. 7427.10 + 7427.07. The rubber fits Peugeot 104, 204 + 304 (front + rear), Peugeot 404 Coupe + Convertible, 504, 205 GTI + CTI rear, 305, 505.

Rubber buffer behind the battery. Suitable for almost all vintage Peugeot (203, 403, 104, 204, 304

404, 504, 604, J7, J9). Or. No. 5611.02

Hook set, 135 mm long. 4 pieces, ideal for removing O-rings, seals, Citroën brake line seals, etc

Contents: 1x straight tip, 1x 90° tip, 1x hook tip, 1x piercing tool.

Retaining clip emblems for Citroen, Renault, Peugeot, old models. 2.5mm inner diameter (i.e. for

2.5mm pins on the emblems). Length: 7.5mm. Per piece

Fixture for angular switches (for mounting under the dashboard). Suitable for switch with 36x18mm

installation hole.

Handhold for lacquer aerosol spray. Facilitates exactly and controlled alloting of the spray. A

real alleviation.

szction pump (hand pump) for eG fuel, hydraulic liquid

Hand washing cream, 500ml

Heater valve seal (rubber ring) down. Suitable for Citroen DS + Peugeot 204/304.

• Suitable for this article
• 
  M5x10 screw, for the heater valve. Suitable for Citroen DS.
  0,27 €

Heater valve plastic housing (screwed on the heat exchanger). For the repair of the heating flow

control valve. Suitable for Citroen DS, GS Birotor, Peugeot 204/304

• Suitable for this article
• 
  Heater valve seal (rubber ring) down. Suitable for Citroen DS + Peugeot 204/304.
  3,48 €

Heli coil application M7. Length: 10,5mm (Thread repair)

Heli coil application M7. Length: 14,0mm (Thread repair)

Heli coil application M7. Length: 7,0mm (Thread repair)

Thread Repair Kit M7x1, for repairing damaged threads. For plating threads in materials with low

shearing strength 1 twist drill, 1 tap, 1 installation tool, 1 tang breaker, 25 x M7x1 coil.

Helicoil repair set for M7. Consisting of: Twist drill (to M12), hand taps from HSS, mounting

spindle, insertion pin breaker (to M12). In each case, 10 theaded inserts M7 in the lengths: 7,0mm, 10,5mm, 14,0mm. Original Helicoil, no reproduction.

Inside roof lining adhesive from Teroson. Contents: 680g. Light, transparent adhesive material for

the roof and door linings.

Roll Pin Assortment, 450 pcs. Diameter from 2 > 10mm, lenght 5>50mm.

Cavity preservation on wax basis, for cavity pistol, 1 litre.

• Suitable for this article
• 
  Underbody coating nozzle (gun) + cavity preservation nozzle (gun), for 1 liter
  26,68 €

Body cavity protection spray, 500 ml. Inclusive hollow space probe

• Suitable for this article

Cavity probe (60cm) for fluid film spray can (21127)

Hone segment 100x10mm (3 fittings) for engine cylinder hone 20918.

Hone segment 30x4mm (2 fittings) for brake cylinder hone 20916.

Y-pipe seal doubles (fusion two in one pipe to the exhaust elbow). Heavy one: 1,0mm. Bore diameter

for each 36,5mm. Suitable for Peugeot 204, Peugeot 304 (engine XL5 + XK5). Peugeot 404, 504, 505, J5, J7. Or. No. 1710.09

Horn (12 V), completely with air compressor + 2 x compressed air horn, relay and air hoses. 750 +

800Hz (2 different tones). 115dB (A). Length of the air horns: 210 + 165mm. Length of the air compressor: about 105mm.

Horn (trumpet) 12 V, high tone. 480Hz, 108dB (A). Very high quality horn, made in the European

Union. The horn is made of metal, with a red cover (trumpet) from plastic! Universal fitting. Diameter: about 110mm. ECE checked.

Horn (trumpet) 12 V, deep tone. 420Hz, 108dB (A). Very high-quality horn, made in the European

Union. The horn is made of metal, with a red cover (trumpet) from red synthetic! Universal fitting. Diameter: about 110mm. ECE checked.

Horn 12 V, high tone. 430Hz, 114dB (A). Very high quality horn, made in the European Union. The

horn is from the front in red painted! Universal fitting. Diameter: about 91mm. Metal housing. ECE checked.

Horn 12 V, deep tone. 340Hz, 114dB (A). Very high quality horn, made in the European Union. The

horn is from the front in red painted! Universal fitting. Diameter: about 91mm. Metal housing. ECE checked.

Horn, 12Volt. Universal fitting. Diameter 100mm! The horn is chromium-plated.

Horn set (2 pieces) chrom-plated, from Bosch. Frequencies: 325 and 400 Hertz. Volume: 118 db(A)

operating voltage: 12 V, power consumption: 48 W each, diameter: 156 mm, depth: 91 mm, EMV protection: included. Universal fitting.

Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach

Suitable for 4,5mm line.

Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach

Suitable for 6,35mm line.

Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach

Suitable for 8,0mm line.

Hydraulic + brake pipe handle to attach, from synthetic. Suitable for 3,75mm line.

Hydraulic + brake pipe handle to attach, from synthetic. Suitable for 4,5mm line.

Hydraulic + brake pipe handle to attach, from synthetic. Suitable for 6,35mm line.

Hydraulic line Brake line flaring tools for use at the vehicle (to use at the car). For all

flanging! For all Citroen lines with 3,5mm, 4,5mm + 6,35mm (1/4 "). For all lines after DIN/CSAE, for flanges of the types CD, E, F, F180 in the usual quantities 4,75mm, 6mm, 8mm, 9mm and 10mm.

• Suitable for this article
• 
  Brake pipe bending pliers! Been suitable for sheet metal, copper, stealing and
  25,29 €

Impregnation spray 500ml, for material hoods, please impregnate the hood at least in spring and

d autumn!

Interior insulation mat (approx 10mm thick), self adhesive, optically as from the years 60s to

approx. end of the 70s. Dimensions: approx. 115 x 55cm (about 600g/m²). These mats have the greenish colour of the original felt mats (made from recycled cotton fibres), but have been manufactured according to today's automotive technology. Flame retardant, no harmful vapours! Completely "Made in Germany". These mats were installed in firewalls, doors, side panels, boot. For the vehicle floor we recommend the mats with a heavy layer (bitumen-like). We have been looking for them for a long time, and finally found some!