engine cooling for Renault AK-AZU

Exhaust air hose from rubber, for Citroen 2CV6. Special preparation. This hose is an genuine

improvement.

• Suitable for this article
• 
  Hose clamp 70 - 90mm. Suitable for exhaust air hose, for Citroen 2CV4 + 2CV6.
  1,98 €

Exhaust air hose Citroen 2CV4, from heat exchanger into the fender. 75mm diameter, 290mm long.

Exhaust air hose Citroen 2CV6, from exhaust heating (heat exchanger) into the fender. 80mm

diameter, 135mm long.

• Suitable for this article
• 
  Hose clamp 70 - 90mm. Suitable for exhaust air hose, for Citroen 2CV4 + 2CV6.
  1,98 €
• 
  2CV, Fender, seal for the exhaust air hose. Or.Nr.AY643-155A
  6,50 €

2CV, Fender, seal for the exhaust air hose. Or.Nr.AY643-155A

• Suitable for this article
• 
  Exhaust air hose Citroen 2CV6, from exhaust heating (heat exchanger) into the
  2,43 €

Grid for the engine fan case (602cc). Suitable for Citroen 2CV6, Dyane 6, Mehari. Very good

reproduction. Securement with 4 screws.

• Suitable for this article
• 
  Screw set (with washers) for the grids for the engine fan case. Suitable for
  2,73 €

Grid for the engine fan case. Suitable for Citroen 2CV6. Reproduction. The grid is galvanized

Securement with 4 screws

• Suitable for this article
• 
  Screw set (with washers) for the grids for the engine fan case. Suitable for
  2,73 €

Screw set (with washers) for the grids for the engine fan case. Suitable for Citroen engines with

602cc + 435cc.

Rubber largely in the engine fan case, mounts before the ignition. Suitable for Citroen 2CV. Made

in Germany.

• Suitable for this article
• 
  Retaining strip for the rubber in the engine fan case. Suitable for Citroen 2CV.
  7,05 €
• 
  Rubber screw set (securement rubber before the ignition, in the engine fan
  15,77 €

Retaining strip for the rubber in the engine fan case. Suitable for Citroen 2CV.

• Suitable for this article
• 
  Rubber largely in the engine fan case, mounts before the ignition. Suitable for
  10,81 €
• 
  Rubber screw set (securement rubber before the ignition, in the engine fan
  15,77 €

Rubber small in the engine fan case, mounts before the ignition. Suitable for Citroen 2CV. Made in

Germany.

Rubber screw set (securement rubber before the ignition, in the engine fan case). Suitable for

Citroen 2CV6, Dyane 6.

Fan blade for 2CV4, Dyane 4, AZU of 250. 8 vanes, color black. Original supplier. Securement with 4

screws. Outside diameter 230mm. Diameter inside: 177mm. Pitch diameter: 162mm.

Fan blade for 2CV6, 9 blades (Or. No. 5433422 or AM241904), Mounted with 6 screws. Outer diameter

265 mm. Inner diameter: approx. 175 mm. Bolt circle: approx. 160 mm. Unfortunately, the quality of this fan blade is not particularly good. Slightly thicker screws may sometimes be required for fitting. The advantage of these fan blades is that they are readily available (the good-quality reproductions are not always in stock) and very low-priced. And once fitted, they work just as well.

• Suitable for this article
• 
  Belt pulley (without fan blade + V-belts) for Citroen 2CV4+6.
  37,58 €
• 
  Belt pulley (without fan blade + V-belt), better than original (Made by
  97,08 €
• 
  Fan blade screw set (6 pieces). Suitable for Citroen 2CV6, Dyane 6.
  4,56 €

Fan blade for 2CV6, 9 vanes, color black. Original supplier. Securement with 6 screws. Outside

diameter 265mm. Diameter inside: 177mm. Pitch diameter: 162mm.

• Suitable for this article
• 
  Belt pulley (without fan blade + V-belts) for Citroen 2CV4+6.
  37,58 €
• 
  Belt pulley (without fan blade + V-belt), better than original (Made by
  97,08 €
• 
  Fan blade screw set (6 pieces). Suitable for Citroen 2CV6, Dyane 6.
  4,56 €

Fan blade screw set (6 pieces). Suitable for Citroen 2CV6, Dyane 6.

Engine starting crank, suitable for Citroen 2CV4 + 2CV6. Reproduction

• Suitable for this article
• 
  lifting jack like original, Citroen 2CV6 + 2CV4
  89,16 €

Screw set suitable for the engine cooling system, for Citroen 2CV6. Contants all screws and nuts to

mount the casing sheets and die sealing behind the oil cooler.

Engine fan case (for drum brake). Suitable for Citroen 2CV6, Dyane, AK, Mehari. Reproduction

Generator cover for Citroen 2CV6. (Cover on engine fan cases above). Or. No. AM532-60A

• Suitable for this article
• 
  V-belt 10x763mm. Suitable for Citroen 2CV6 + 2CV4, up to the year of
  7,14 €

Tie-clip for the engine cowling sheet metal, for Citroen 2CV (8 per side are required. (to it

suitable screw = 20170)

• Suitable for this article
• 
  Sheet metal driving screw with large head, black galvanizes. Measurements: 4.2
  0,38 €

Engine cowling around the liner, above on the left (air circulation). Material sheet metal

Suitable for Citroen 2CV6

Engine cowling around the liner, above on the right (air circulation). Material sheet metal

Suitable for Citroen 2CV6

Engine cowling around the liner, down on the left (air circulation). Material sheet metal. Suitable

for Citroen 2CV6.

Engine cowling around the liner, down on the right (air circulation). Material sheet metal

Suitable for Citroen 2CV6.

Engine cowling set (4 pieces), for Citroen 2CV6. Reproduction out of sheet metal! (Air circulation

around liners).

• Suitable for this article
• 
  Tie-clip for the engine cowling sheet metal, for Citroen 2CV (8 per side are
  0,57 €
• 
  Sheet metal driving screw with large head, black galvanizes. Measurements: 4.2
  0,38 €

Belt pulley (without fan blade + V-belts) for Citroen 2CV4+6.

• Suitable for this article
• 
  Belt pulley, screw for the securement of the belt pulley on the crankshaft
  2,93 €
• 
  Fan blade for 2CV6, 9 vanes, color black. Original supplier. Securement with 6
  25,68 €

Belt pulley (without fan blade + V-belt), better than original (Made by Franzose). Suitable for

Citroen 2CV6, Dyane, Mehari. The belt pulley has been rotated from a 18kg steel block DIN 1,0501 (AISI/SAE 1040, EN C35). Fine balanced pulley, thus avoiding much pressure on the crankshaft. No risk of tearing off as it is not welded. Belt pulley is yellow galvanised (like original). Made by Franzose/Cipere, entire production process in Europe.

• Suitable for this article
• 
  Belt pulley, screw for the securement of the belt pulley on the crankshaft
  2,93 €
• 
  Fan blade for 2CV6, 9 vanes, color black. Original supplier. Securement with 6
  25,68 €
• 
  Fan blade screw set (6 pieces). Suitable for Citroen 2CV6, Dyane 6.
  4,56 €

Belt pulley, screw for the securement of the belt pulley on the crankshaft. Suitable for Citroen

2CV, with generator propulsion over V-belts. (2CV6 + 2CV4)

• Suitable for this article
• 
  14mm nut for the belt pulley. Suitable for Citroen 2CV. The nut is thin-walled
  4,86 €
• 
  spring washer M10, galvanized
  0,24 €

Screw, for the securement of the belt pulley, on the crankshaft. Suitable for Citroen 2CV 16 HP

not fitting for 2CV6! Or.Nr. A24195

Hose clamp 11-17mm, especially for radiator hose. Vintage look. Embossed band with raised edges

This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.

• Suitable for this article
• 
  Hose clamp Screwdriver hexagon (7mm). Flexible. Ideal for our hose clamps with
  24,69 €

Hose clamp 13-20mm, especially for radiator hose. Vintage look. Embossed band with raised edges

This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.

• Suitable for this article
• 
  Hose clamp Screwdriver hexagon (7mm). Flexible. Ideal for our hose clamps with
  24,69 €

Hose clamp 15-24mm, especially for radiator hose. Vintage look. Embossed band with raised edges

This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.

• Suitable for this article
• 
  Hose clamp Screwdriver hexagon (7mm). Flexible. Ideal for our hose clamps with
  24,69 €

Hose clamp 19-28mm, especially for radiator hose. Vintage look. Embossed band with raised edges

This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.

• Suitable for this article
• 
  Hose clamp Screwdriver hexagon (7mm). Flexible. Ideal for our hose clamps with
  24,69 €

Hose clamp 22-32mm, especially for radiator hose. Vintage look. Embossed band with raised edges

This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.

• Suitable for this article
• 
  Hose clamp Screwdriver hexagon (7mm). Flexible. Ideal for our hose clamps with
  24,69 €

hose clamp for 15-20mm.

hose clamp for 40-60mm.

Hose clamp Screwdriver hexagon (7mm). Flexible. Ideal for our hose clamps with raised edges.

• Suitable for this article
• 
  Hose clamp 11-17mm, especially for radiator hose. Vintage look. Embossed band
  3,67 €
• 
  Hose clamp 13-20mm, especially for radiator hose. Vintage look. Embossed band
  3,62 €
• 
  Hose clamp 15-24mm, especially for radiator hose. Vintage look. Embossed band
  3,87 €
• 
  Hose clamp 19-28mm, especially for radiator hose. Vintage look. Embossed band
  4,21 €
• 
  Hose clamp 22-32mm, especially for radiator hose. Vintage look. Embossed band
  4,12 €
• 
  Hose clamp 26-38mm, especially for radiator hose. Vintage look. Embossed band
  4,26 €
• 
  Hose clamp 32-44mm, especially for radiator hose. Vintage look. Embossed band
  4,56 €
• 
  Hose clamp 38-50mm, especially for radiator hose. Vintage look. Embossed band
  4,71 €
• 
  Hose clamp 40-56mm, especially for radiator hose. Vintage look. Embossed band
  4,91 €
• 
  Hose clamp 57-75mm, especially for radiator hose. Vintage look. Embossed band
  5,86 €