Universal joint suitable for the drive shaft, for Citroen 2CV from the sixties + fifties
Reproduction. 25mm diameter, 57mm long. Significant reproduction. Or.Nr.: A37203
for Alle 2CValt
1702 Articles | Page 21 of 35
Universal joint suitable for the drive shaft, for Citroen 2CV from the sixties + fifties
Reproduction. 25mm diameter, 61mm long. Or.Nr.: A37203
Elbow seal suitable for inlet + exhaust, for Citroen 2CV with 12 HP engine. (Vehicles with 3
connectors of the Inlet + exhaust manifold). Significant reproduction of the original manufacturer!
Elbow seal inlet + exhaust for Citroen 2CV old. The seals are installed with vehicles, whose elbow
spider with 3 screws per side are fastened.
Inlet + Exhaust manifold for 2CV (425ccm engine upto 09/1966), without attachment for generator
r, reproduction. Or.no.: AK1411
Clutch set for 2CV old, from 1955 to 1966, clutch disk with 10 splines, centrifugal clutch
reproduction. 160mm diameter. Note: The clutch must be adjusted after Citroen work instruction!
PDF FILE Clutch set for 2CV old, from 1955 to 1966, clutch disk with 10 splines. Normal gear shift
Reproduction. 160mm diameter. Made in EU
Clutch disk centrifugal clutch. Suitable for Citroen 2CV starting from year of construction
04/1966. 160mm diameter. 18 teeth. Or.Nr.AZ313-01C
Clutch Alignment Tool, Universal. For single plate clutches. Suitable for flywheels with or without
pilot bearing. Fast to fit and remove. Universal applications. Size of collets: 14mm to 28mm across 3 adaptors. Cone size range from 35mm < 67mm (for almost all classical french cars)
Flashing - park light caps (2 fittings), for Labinal light. Suitable for Citroen 2CV, of year of
construction 09/1957 to 03/1963.
Labinal seals at the bottom, for the Labinal flashing parking light. These two seals for the left
and right sides are manufactured using high-quality 3D printing. Suitable for Citroën 2CVs with a year of construction ranging from 09/1957 to 03/1963.
Bearing flange (ring) for the drive shaft in the wheel hub. Suitable for Citroen 2CV starting from
year of construction 1966, with constant velocity drive shafts. Or.Nr.A37396.
Bearing on the left, for the connection of the drive shaft in the gearbox. Suitable for Citroen
2CV4 starting from year of construction 1963 (not for 2CV6). Original Citroen, Or.Nr.: AZ3319H
Steering gear repair set for the tie rod guide. Suitable for Citroen 2CV. Consisting of: Pin + seat
bowls + guides, ball pin, rubber,
Steering wheel with steering column. Completely produced of metal. Suitable for Citroen 2CV first
years of construction. New part. The steering wheel is only grounding and must be painted. Bottom edge steering wheel to steering column end = 770mm. Bottom edge steering wheel to center screw for steering column securement = 762mm.
Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. Splines (worm gears) are continuous
up to the bearing. Suitable bush = 12233.
Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. First version. Splines (worm gears)
go only up to the half height of the bearing. Shaft diameter at the lower end = 13 mm.
Steering worm bearing bush (down at the needle bearing). Suitable for Citroen 2CV. The bearing is a
needle bearing! Only for steering worms with 8 teeth. Inside diameter: 12mm. Outside diameter: 18mm. Overall height: 12mm. Manufacturer SKF.
Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF
Inside diameter 10mm, outside diameter 17mm, height of 12mm
Steering worm locking cap down (the cap is hit from downside into the steering gear). 20mm
Suitable for Citroen 2CV.
Steering worm nut with sealing ring. Suitable for Citroen 2CV, starting from year of construction
03/1971. From own production, with interchangeable shaft seal. Very significant.
Steering worm nut shaft seal (as substitute for 12140). Suitable for Citroen 2CV, starting from
year of construction 03/1971. Dimension: 19 x 27 x 5mm.
Steering column sealing rubber down on the pedal base. Suitable for Citroen 2CV, with metal
steering wheel (2CV from the fifties). Dimension: 70 x 22 x 12mm. Or. No. A44218.
Steering column sealing rubber, for the feed-through in the pedal floor (the rubber is supplied
without sliding ring). Suitable for Citroen 2CV4 + 2CV6.
Steering column securing clip (on the steering gear). Suitable for Citroen 2CV starting from year
of construction 09/1971. Made in Germany.
Steering unit, repair set. Suitable for Citroen 2CV. Consisting of: Guide steering unit pin, 2x
slide ring, ring for the gear rack ((27,75mm + - 1/10mm), rubber under the tie rods. Reproduction. Only for LHD, cannot use for RHD.
Light + horn switch in grey for Citroen 2CV (1961 > 1970), 11CV, HY. Reproduction. The switch has
only 1 horn function (no town and country horn).
Light + horn switch in black 2CV, reproduction, looks like the 50's version, fits also for HY
Y, 11cv. The switch has only 1 horn function (no town and cross-country horn).
Generator Brush Set Citroen 2CV old, 6 V technology. For generators are mounted on the crankshaft
Measurements of 7,9x22mm. File on measure and remove a cable.
Generator Brush Set DUCELLIER, for Citroen 2CV, from year of construction 1949 to 1960. Comparison
n designation UX36, measurements: 15.5 x 5.2 x 17,5mm.
1702 Articles | Page 21 of 35
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
