steering gear for Citroën 2CV 2CV4
31 Articles
Steering gear repair set for the tie rod guide. Suitable for Citroen 2CV. Consisting of: Pin + seat
bowls + guides, ball pin, rubber,
Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. Splines (worm gears) are continuous
up to the bearing. Suitable bush = 12233.
Steering worm bearing bush (down at the needle bearing). Suitable for Citroen 2CV. The bearing is a
needle bearing! Only for steering worms with 8 teeth. Inside diameter: 12mm. Outside diameter: 18mm. Overall height: 12mm. Manufacturer SKF.
Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF
Inside diameter 10mm, outside diameter 17mm, height of 12mm
Steering worm locking cap down (the cap is hit from downside into the steering gear). 20mm
Suitable for Citroen 2CV.
Steering worm nut with sealing ring. Suitable for Citroen 2CV, starting from year of construction
03/1971. From own production, with interchangeable shaft seal. Very significant.
Steering worm nut shaft seal (as substitute for 12140). Suitable for Citroen 2CV, starting from
year of construction 03/1971. Dimension: 19 x 27 x 5mm.
Steering unit, repair set. Suitable for Citroen 2CV. Consisting of: Guide steering unit pin, 2x
slide ring, ring for the gear rack ((27,75mm + - 1/10mm), rubber under the tie rods. Reproduction. Only for LHD, cannot use for RHD.
Tie rods slide ring squarely (1 oversize), mounts in the steering gear. Suitable for Citroen 2CV
Reproduction from a brass alloy. Oversize: about 8 x 13 x 21mm.
Tie rods slide ring squarely, mounts in the steering gear. Suitable for Citroen 2CV. Reproduction
from a brass alloy. Standard measurement about 8x13x20.
Front axle cover sheet. (Cover at the steering gear, below the tie rod securement). Suitable for
Citroen 2CV. Or. No.: A44278A
Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suitable
for Citroen 2CV. Or.Nr.A44295
Front axle pipe - steering gear in the exchange. Suitable for Citroen 2CV4 + 2CV6. Top outdated
all bearings and pinions are accurately bedded in and measured. The steering worm and the gear rack are re-tooled with grease nipple. To lubricate thus at any time from the outside. 250 euros Old part deposit.
Gear rack ring in the axle tube (steering gear). Suitable for Citroen 2CV. Reproduction. First
oversize. Outside diameter: about 34,2mm. Inside diameter: 27,5mm.
Gear rack ring in the axle tube (steering gear). Suitable for Citroen 2CV. Reproduction. Standard
dimension. Outside diameter: about 34,00mm. Inside diameter: 27,50mm.
Gear rack ring in the axle tube (steering gear). Suitable for Citroen 2CV. Reproduction. Second
oversize. Outside diameter: about 34,3mm. Inside diameter: about 27,5mm.
Gear rack ring in axle tube 2CV. Reproduction. Made in European Union. Outside diameter 34,05mm
inside diameter 27,50mm.
Gear rack ring in axle tube 2CV. Reproduction. Made in European Union. Outside diameter 34,10mm
inside diameter 27,50mm.
Gear rack ring in axle tube 2CV. Reproduction. Made in European Union. Outside diameter 34,15mm
inside diameter 27,50mm.
Gear rack ring in axle tube 2CV. Reproduction. Made in European Union. Outside diameter 34,25mm
inside diameter 27,50mm.
Gear rack steering unit, 19 teeth. Suitable for Citroen 2CV, starting from year of construction
1955. This gear rack is only Installed by vehicles, which have an steering worm with 7 teeth. Or. No.: A4424b
Steering rack, up to Orga no. 2276. Suitable for Citroen 2CV (steering pinion with 7 teeth). 24
teeth, total length: 365mm. Replica
31 Articles
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
