for Citroën 2CV Mehari
1648 Articles | Page 14 of 33
Screw set (2 item) for the securement the lever (parking brake) at the brake caliper. Suitable for
Citroen 2CV6, Dyane, Mehari, AMI8.
Heating air fan for the installation into the heating hose of Citroen 2CV. The hose is cut through
and mounted then the fan between the heating hose ends. Optically almost invisibly. The mounting material is provided. The fan has the following dimensions: 80mm diameter, construction length 50mm.
Heater hose on the left of Citroen Mehari. Diameter 70mm, 580mm long, isolate with 10mm foam
m material. Heat exchanger to distributor in the front wall.
Heater hose on the right of Citroen Mehari. Diameter 70mm, 490mm long, isolated with 10mm foam
material. Heat exchanger to distributor in front wall.
Heater cable sheet metal holder, securement of the heater cable on the heat exchanger. This sheet
metal holder is for both heater cables. Suitable for Citroen 2CV.
Heater cable sheet metal holder, securement of the heater cable on the heat exchanger. This sheet
metal holder is for one heater cable. Suitable for Citroen 2CV.
Heater cable short, suitable for Citroen 2CV, for all years of construction. Installed one between
the heating exchangers in the engine compartment. Depending upon year of construction it can be possible that the cable must be cut.
Heater cable tension force clamp (wide) on the heat exchangers, for Citroen 2CV. With this tension
force clamp the two heater cables are adjusted. Significant after production from the European Union. Or.Nr. AZU 644-101
Heater cable tension force clamp (wide) on the heat exchangers, for Citroen 2CV. With this tension
force clamp the two heater cables are adjusted. Or.Nr. AZU 644-101
Thread Repair Kit M7x1, for repairing damaged threads. For plating threads in materials with low
shearing strength 1 twist drill, 1 tap, 1 installation tool, 1 tang breaker, 25 x M7x1 coil.
Helicoil repair set for M7. Consisting of: Twist drill (to M12), hand taps from HSS, mounting
spindle, insertion pin breaker (to M12). In each case, 10 theaded inserts M7 in the lengths: 7,0mm, 10,5mm, 14,0mm. Original Helicoil, no reproduction.
Horn (12 V), completely with air compressor + 2 x compressed air horn, relay and air hoses. 750 +
800Hz (2 different tones). 115dB (A). Length of the air horns: 210 + 165mm. Length of the air compressor: about 105mm.
Horn (trumpet) 12 V, high tone. 480Hz, 108dB (A). Very high quality horn, made in the European
Union. The horn is made of metal, with a red cover (trumpet) from plastic! Universal fitting. Diameter: about 110mm. ECE checked.
PDF FILE Horn (trumpet) 12 V, deep tone. 420Hz, 108dB (A). Very high-quality horn, made in the European
Union. The horn is made of metal, with a red cover (trumpet) from red synthetic! Universal fitting. Diameter: about 110mm. ECE checked.
Horn 12 V, high tone. 430Hz, 114dB (A). Very high quality horn, made in the European Union. The
horn is from the front in red painted! Universal fitting. Diameter: about 91mm. Metal housing. ECE checked.
Horn 12 V, deep tone. 340Hz, 114dB (A). Very high quality horn, made in the European Union. The
horn is from the front in red painted! Universal fitting. Diameter: about 91mm. Metal housing. ECE checked.
Horn set (2 pieces) chrom-plated, from Bosch. Frequencies: 325 and 400 Hertz. Volume: 118 db(A)
operating voltage: 12 V, power consumption: 48 W each, diameter: 156 mm, depth: 91 mm, EMV protection: included. Universal fitting.
Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach
Suitable for 4,5mm line.
Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach
Suitable for 6,35mm line.
Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach
Suitable for 8,0mm line.
Hydraulic line and Brake line flaring tool for use at the vehicle! For all lines with 3,5mm, 4,5mm
6,35mm (1/4 "). (Citroen)
Hydraulic line Brake line flaring tools for use at the vehicle (to use at the car). For all
flanging! For all Citroen lines with 3,5mm, 4,5mm + 6,35mm (1/4 "). For all lines after DIN/CSAE, for flanges of the types CD, E, F, F180 in the usual quantities 4,75mm, 6mm, 8mm, 9mm and 10mm.
Brake line flaring tool, for brake and hydraulic lines. Particularly for Citroen connectors. With
thrust pieces for 3,5mm + 4,5mm lines (8,0mm + 9,0mm Clinch screws).
Hydraulic hose rubber 4.5 mm LHS (red) + normal brake fluid DOT3 + DOT4. Top quality (new improved
reproduction made from EPDM). Suitable for Citroen DS with LHS hydraulic system, Citroen HY + 2CV, AMI with 4.5 mm brake line (9 mm screw connection).
Interior insulation mat (approx 10mm thick), self adhesive, optically as from the years 60s to
approx. end of the 70s. Dimensions: approx. 115 x 55cm (about 600g/m²). These mats have the greenish colour of the original felt mats (made from recycled cotton fibres), but have been manufactured according to today's automotive technology. Flame retardant, no harmful vapours! Completely "Made in Germany". These mats were installed in firewalls, doors, side panels, boot. For the vehicle floor we recommend the mats with a heavy layer (bitumen-like). We have been looking for them for a long time, and finally found some!
Interior insulation mat (approx 15mm thick), self adhesive, optically as from the years 60s to
approx. end of the 70s. Dimensions: approx. 115 x 55cm (about 900g/m²). These mats have the greenish colour of the original felt mats (made from recycled cotton fibres), but have been manufactured according to today's automotive technology. Flame retardant, no harmful vapours! Completely "Made in Germany". These mats were installed in firewalls, doors, side panels, boot. For the vehicle floor we recommend the mats with a heavy layer (bitumen-like). We have been looking for them for a long time, and finally found some!
Interior insulation mat (approx 20mm thick), self adhesive, optically as from the years 60s to
approx. end of the 70s. Dimensions: approx. 115 x 55cm (about 1200g/m²). These mats have the greenish colour of the original felt mats (made from recycled cotton fibres), but have been manufactured according to today's automotive technology. Flame retardant, no harmful vapours! Completely "Made in Germany". These mats were installed in firewalls, doors, side panels, boot. For the vehicle floor we recommend the mats with a heavy layer (bitumen-like). We have been looking for them for a long time, and finally found some!
Interior insulation mat for the floor (10mm thick), optically as from the years 60s to approx. end
of the 70s. Dimensions: approx. 105 x 55cm (approx. 2900g/m²). These mats have the greenish colour of the original felt mats, with an additional heavy layer (modern bitumen, does not age, does not crack, UV resistant, water repellent, state-of-the-art automotive technology, but with the look of the old days!) The insulation material is flame retardant, no harmful vapours! Completely "Made in Germany". These mats are laid on the vehicle floor or cardan tunnel. Heavy layer to the carpet side! The heavy layer also prevents "droning noises". The mats can be deformed by heat and adapt to the contours.
Interior insulation mat for the floor (approx 15mm thick), optically as from the years 60s to
approx. end of the 70s. Dimensions: approx. 105 x 55cm (approx. 3200g/m²). These mats have the greenish colour of the original felt mats (made from recycled cotton fibres), with an additional heavy layer (modern bitumen, does not age, does not crack, UV resistant, water repellent, state-of-the-art automotive technology, but with the look of the old days!) The insulation material is flame retardant, no harmful vapours! Completely "Made in Germany". These mats are laid on the vehicle floor or cardan tunnel. Heavy layer to the carpet side! The heavy layer also prevents "droning noises". The mats can be deformed by heat and adapt to the contours.
Interior insulation mat for the floor (approx 20mm thick), optically as from the years 60s to
approx. end of the 70s. Dimensions: approx. 105 x 55cm (approx. 3500g/m²). These mats have the greenish colour of the original felt mats (made from recycled cotton fibres), with an additional heavy layer (modern bitumen, does not age, does not crack, UV resistant, water repellent, state-of-the-art automotive technology, but with the look of the old days!) The insulation material is flame retardant, no harmful vapours! Completely "Made in Germany". These mats are laid on the vehicle floor or cardan tunnel. Heavy layer to the carpet side! The heavy layer also prevents "droning noises". The mats can be deformed by heat and adapt to the contours.
1648 Articles | Page 14 of 33
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
