for Citroën 2CValt
1703 Articles | Page 4 of 35
2CV, boot lid trim (3 parts, made from 8mm natural fleece). Felt light grey. The trim must be glued
in place. Made in Germany.
2CV, boot lid trim (3-piece, made from natural fleece). Black felt with a backing layer of
sound-deadening material. The trim must be glued in place. Made in Germany.
2CV, Luggage compartment lid, emblem (signature) "2CV", from synthetic chromium-plates. Length
about 55mm, height of ca.21mm.
2CV, Luggage compartment lid, emblem (signature) "2CV4", from synthetic chromium-plates. Length
about 85mm, height of ca.25mm
2CV, Luggage compartment corner on the left, transition baggage compartment floor sheet metal to
the rear end panel. Suitable for Citroen 2CV. Made in Europe.
2CV, Luggage compartment corner on the left, transition baggage compartment floor sheet metal to
the rear end panel. Suitable for Citroen 2CV. Made in Europe.
2CV, Luggage compartment hood. Emblem "2CV" swung, from 3mm high-grade steel. Made in Germany by
Franzose. The signature 16836 consists of: 1x "2" + 1x "CV". The emblems are fastened with 4x M3 nuts (our article number 20166).
2CV, Luggage compartment hood. Emblem "CITROEN" swung, from 3mm high-grade steel. Made in Germany
by Franzose. The signature is about 180mm long, and 65mm highly. The emblems are fastened with 2x M3 nuts (our article number 20166).
2CV, Trunk lock, locking pivot short (Square pin that the lockcylinder takes up). Attention: There
are cheaper replicas from Asia that break very quickly. !! Please order the retaining clip 16391 for the locking cylinder separately or reuse the old one!
2CV, Fender rear, seal synthetic transparency, between fender and the C-support. Sutiable for
Citroen 2CV. Or.Nr. 5452990
2CV, Fender rear, fixing clip for the fender down at the body. Per page 1 clip is required
Suitable for Citroen 2CV.
Fender rear, screw set from high-grade steel, for the securement fender at the C-support and in the
wheel housing. Suitable for Citroen 2CV. Consisting of: 4x M5x16 DIN 85A2 + 3x 6,3x 19 DIN 7976 A2.
VIDEO 2CV, fenders front + rear. Stone guards corner (6 pieces) for the front fenders (under the front
turn signals) + rear on the front fender (above the mud flaps). Additionally on the front of the rear fenders. So, 1 complete set for the 2CV. Material: Polished cast aluminium
2CV, Fender in front, fixing clip for the starting crank. By the Citroen 2CV up to 1970, was
fastened the starting crank inside to the fender.
2CV, Fender in front, cap nut from high-grade steel. For the securement of the front fenders at the
box sill. Suitable for Citroen 2CV.
2CV, Fender in front, nut for the securement! With integrated rotatable washer, like in the first
years of production. The lacquer will not be damaged if you tighten up the nut.
2CV, fender in front. Nut for the securement, like original. Suitable for Citroen 2CV, starting
from year of construction 1963 to 1990. The nut is galvanized and has a broader seating.
2CV, front wing, hollow rivet for fixation of mud flap! Finally the mud flap can be mounted again
with the original hollow rivets. Price per piece! (for a vehicle 8 rivets required).
2CV, front wing, hollow rivet head setter! This tool enables the original appearance of the hollow
rivet, after mounting. For the perfectionists among you! (it can also work using a hammer, but it does not look fine!)
2CV, Fender in front, stone guards (1 pair) rear, at the front fenders. (Above the mud flaps)
Suitable for Citroen 2CV, all years of construction. Material: Aluminum casting polished.
2CV, Fender in front, stone guards (1 pair) underneath the indicators, for the front side of the
e fender. Suitable for Citroen 2CV, all years of construction. Material: Aluminum casting polished.
2CV, fender screw outside, rear at C-support. Suitable for Citroen 2CV. Optically 100% like the
original screws! Size: M5x16. Original, the srews were painted in fender color!
Fender screw rear, inside in the wheel housing. Suitable for Citroen 2CV. The screw fits also in
the Dyane, the securement of the front fenders + Renault R4. Reproduction from high-grade steel. Optically it`s a small different to the original ones. Measurements: 6,3x19
2CV, Fender screw rear, inside in the wheel housing. Suitable for Citroen 2CV. The screw fits also
by the Dyane, for securement of the front fenders! Reproduction made of metal, to 100% like original!
2CV, radiator grille, fly screen behind the radiator grille. Suitable for Citroen 2CV, from the
year of construction 1963 to 1969, first version after the corrugated metal bonnet. For radiator grille made of aluminium with large double angle (item no. 16096). This fly screen can also be used for 2CV6 up to the year of construction 1990.
2CV, Radiator grill, winter protection simply. Material: Vinyl. The winter protection is hooked
only from the outside at the aluminum radiator grill. Suitable for Citroen 2CV, of year of construction 1963 to 1973. Note: Not suitable for radiator grill from synthetic!
Ventilation shutter seal rubber, for Citroen 2CV, all models. This rubber is a quality after
production, and corresponds to the original rubber.
Ventilation shutter 2CV to 1963/64. Without attachments. Linking of the ventilation shutter is
about centric! The seal and the trim are the same, than from the other 2CV. Made in Europe.
1703 Articles | Page 4 of 35
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
