Ventilation shutter completely (original), for Citroen 2CV. The Ventilation shutter is supplied
with seal and trim! The Ventilation shutter must paint before be adapted! Original Citroen, no reproduction!
for Citroën 2CValt
1703 Articles | Page 5 of 35
Ventilation shutter completely, for Citroen 2CV. Reproduction out of sheet metal. The Ventilation
shutter is supplied with seal and trim! The Ventilation shutter must be adapted at the vehicle, before it is painted.
Ventilation shutter aluminum strip, 2CV. The strip is a little more matte than the original. 12x
nut M3 (20166) are required!
Ventilation shutter trim from polished high-grade steel, suitable for Citroen 2CV. Own
reproduction. 12 x nut M3 are required. (20166)
2CV, ventilation flap, re-fitting grid for air distribution towards the driver. This ingenious
little grid redirects the airflow towards the driver when the ventilation flap is open. The grid is fitted within couple of minutes, using the clips supplied. So: ventilation system variable according to speed! We wouldn't want to do without it at high temperatures!
PDF FILE Ventilation shutter, pin for Ventilation shutter linking (without clamp), Citroen 2CV, for all
years of construction. Diameter: 5,0mm
Securing clip suitable for the Ventilation shutter, for Citroen 2CV. (Securement installing
handwheel at the Ventilation shutter)
2CV, brass bushings in pedal floor for standing brake pedal + clutch pedal (guide for the pedals in
the floor panel). Suitable for Citroen 2CV, AZU up to approx. year of construction 1970.
2CV, Bonnet, damming mat from material - felt. Not self adhesive. This bonnet insulating mat was
the first version, and installed from 1963 to about 1969.
2CV, Bonnet, rubber buffer small, for the base of the bonnet on the fender. The rubber buffers are
from the inside, in front, in the bonnet mounted.
2CV, Bonnet, retaining rubber (bearing) for the bonnet support, in front at the head light bracket
Suitable for Citroen 2CV starting from year of construction 1961. Citroen AMI6
2CV, Bonnet, retaining rubber suitable for the bonnet hinge rod, for Citroen 2CV. If the bonnet is
opened, the bonnet rod is hooked there.
2CV, Bonnet, catch completely. Suitable for Citroen 2CV. Installed from 1961 to 1973. The hood
catch is screwed onto the chassis. Or.Nr. AZ86102
2CV, Bonnet, trim (aluminum) for the bonnet. Version AZAM. The trim is in the cross section easily
triangular. Length about 106cm. Wide one: 20mm. This trim fits on each 2CV starting from the year of construction 1963.
Bonnet, trim with mounting material. The trim fits on all Citroen 2CV bonnets starting from year of
construction 1961. Length about 93cm. The trim does not fit on the corrugated sheets bonnet!
2CV, bonnet hinge strip with repair sheet metal up to the Ventilation shutter. Suitable for Citroen
2CV. Good reproduction, like original. The sheet metal has the projection up to the ventilation shutter. Made in Europe.
2CV, engine bonnet hinge ledge, with repair sheet metal up to the Ventilation shutter. For Citroen
2CV. Simple reproduction. Made in Germany.
2CV old, pedal floor plate doubles (with brass bushes). Strengthened version. For all Citroen 2CV
with standing brake + clutch pedal (installed until about 1970). The pedal floor plate is electrolytically coated (very good rust protection). The pedal floor plate has like original 2 brass bushes in front, for the clutch and the brake. Made in Europe.
2CV, Pedal floor plate doubles. Strenghened version. For all Citroen 2CV with standing foot
throttle and hanging brake pedal + clutch pedal. (Installed about 1970 to 1977.) The pedal floor plate is electrolytically coated (very good rust protection). Made in Europe.
2CV old, pedal floor plate doubles. Strengthened version. For all Citroen 2CV with standing brake +
clutch pedal (installed until about 1970). The pedal floor plate is electrolytically coated (very good rust protection). Made in Europe.
2CV, Pedal floor plate inside, with all flanges (Repair sheet metal). Very good reproduction, for
Citroen 2CV with hanging pedals. Made in Europe.
- Suitable for this article
2CV, Crossbeam fixture (gusset sheet plate) on the left for Citroen 2CV. This gusset sheet plate is
for the mounting on the left for the medium crossbeam above at the roof. Made in Europe.
2CV, Crossbeam fixture (gusset sheet plate) on the left for Citroen 2CV. This gusset sheet plate is
for the mounting on the left for the medium crossbeam above at the roof. Made in Europe.
2CV, wheel housing body edge rear on the left, (up to the rear end panel). Improved version
Heavier sheet metal and longer than our number 15198.
2CV, Wheel housing body edge at the rear left. Very often the overlapping sheet metal on the rear
end panel is rusty (beside the tail lamps). Made in Europe.
2CV, wheel housing body edge rear on the right, (up to the rear end panel). Improved version
Heavier sheet metal and longer than our number 15199.
2CV, Wheel housing body edge at the rear right. Very often the overlapping sheet metal on the rear
end panel is rusty (beside the tail lamps). Made in Europe.
Soft top hood, sheet metal driving screw from high-grade steel. For the push-button lower part of
the soft top hood, on the body. 3.5 x 16 mm
Back window seal - sealing trim, synthetic grey. Suitable for Citroen 2CV. Length: 2,23 meters
This sealing trim was used also with the side windows in Citroen a AK, AZU, Dyane, HY. Made in France
2CV, conversion kit, in order to convert soft top hoods from outside closing to inside closing
Consisting of: 1x soft top hood bow with hinge, 2x soft top hood buckle inside. For the replacement an inside closing soft top hood it is necessary, that the front cross beam has the pins for the connection with the folding clamp.
2CV, Soft top hood closing cap in front on the left from aluminum casting. Note: Only suitable for
2CV with roll roof buckle outside!. Bore for the connector must be adapted depending upon year of construction.
2CV, Soft top hood closing cap in front on the right from aluminum casting. Note: Only suitable for
2CV with roll roof buckle outside!. Bore for the connector must be adapted depending upon year of construction possibly.
2CV, Roll roof lug, suitable on the left above at the windshield frame and on the right rear on the
rear end panel! For Citroen 2CV, Installed over all years of construction!
VIDEO 
2CV, Roll roof lug, suitable on the right above at the windshield frame and on the right left on
the rear end panel! For Citroen 2CV, Installed over all years of construction!
Head light bracket 2CV old, second version! For 2CV starting from year of construction 1961. (The
first models after corrugated sheet bonnet!)
Head light bracket 2CV old. First version for corrugated sheet bonnet. Suitable for Citroen 2CV, to
year of construction 1961. Original of MCC France.
1703 Articles | Page 5 of 35
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
