Alle / Alle / steering gear

Cover sheet (sliding sheet metal, in front + rear suitable) for the case of the steering gear. Suitable for Citroen 11CV sheet Or. Nr.601938 + 601939

Quality: 4

Cap (aluminum) on the left, for the steering gear. Suitable for Citroen 11CV + 15CV. Or. No. 602008

Quality: 3

Cover semicircular, on the steering rack. Suitable for Citroen 11CV BN + 15CV. Length: 500mm. Or. No. 60197

Quality: 3

Sticker "steering gear", Citroën Mehari.

Quality: 3

Spacer 0,3mm (3 item), for the lower steering gear case (between steering column bottom and steering gear). Suitable for Citroen HY. Or. Nr. HY442-81B

Quality: 3

Sheet metal cap on the tie rod pin. Suitable for Citroen 11CV + 15CV. Or. No. 602046

Quality: 3

Pin in steering gear. (2x pin, 3x seat bowl). Repair kit. The pins take up the tie rods. Suitable for Citroen 11CV. Or.Nr. 601847, 601849, 601836

Quality: 3

Dauphine, collar steering gear (per piece). Openings 31mm + 25mm. Minimum lengthens 95mm, maximum length 230mm. Diameter over all 68mm.

Quality: 4

Spring for gear racks thrust piece (in the steering gear). Suitable for Citroen 2CV. Or.Nr.A4422

Quality: 4

Spring plate, centrically on the steering gear. Suitable for Citroen DS. Or. No. DX442-120

Quality: 3

Rubber seal on the steering unit pin. Dimension: 32 x 16mm. Suitable for Citroen 11CV + 15CV. Or. No. 601946

Quality: 3

Rubber seal centrically, for the steering gear. Suitable for Citroen DS. Dimension: 16.5 x 28.5 x 9mm. Or. No. 3D5411158K

Quality: 3

Rubber washer (seal) steering column at the body. Suitable for Citroen 11CV + 15CV. 130 x 110mm. Or. No. 232298

Quality: 3

Flexible disk for the steering column. Suitable for Renault R4, R5, R8, R16, R18, Dauphine. Outside diameter: 76mm. Inside diameter: 24mm. Pitch center diameter: about 50mm.

Quality: 3

Hydraulic pipe on the steering gear (power steering - gear rack case). Suitable for Citroen DS. Or. No. 5D 5416960A

Quality: 3

Hydraulic pipe on the steering gear (power steering - gear rack case). Suitable for Citroen DS. Or. No. 5D 5417048G

Quality: 3

Hydraulic pipe on the steering gear (power steering - gear rack case). Suitable for Citroen DS. Or. No. DXN394-29

Quality: 3

• Suitable for this article
• Sealing ring (O-ring), for the semi-automatic transmission and above at the steering gear. Suit
  0,75 €

Ball - sliding nut in the steering gear. Suitable for Citroen 11CV + 15CV. Measurement: 36.8 x 23,5mm. Or.Nr. 601843

Quality: 3

Ball pin (2x) with bearing shells (4x), for the steering gear. Suitable for Citroen HY, starting from year of construction 04/1969. Ball pin length: 84mm. Thread: M12 x 1,5. Or. No. HY442-100. Bearing shells diameters: 28mm. Amount: 11,7mm. Or. No. HY442-242A. Since the year of construction 05/1972, the bearing shells are Installed.

Quality: 3

Top bearing , for steering worm. Suitable for Citroen 11CV. Dimension: 50.5 x 16,8mm.

Quality: 3

Bearing bush with rubber, for the steering column at the top. Suitable for Citroen 11CV + 15CV. Citroen HY, to year of construction 1965. Dimension: 36.7 x 22.5 x 30mm. Or. No. 604129 + 604130

Quality: 3

Bearing for the steering column bottom (needle bearing bush). Suitable for Renault R5, Super5, Rapid, R9, R11, R18, R25, R30, Alpine, Espace 1, Fuego, Master 1. Inner diameter: 18,5mm. Outside diameter: 37,0mm. Overall height: 20mm. Or. No. 7703090293

Quality: 3

Steering gear for Citroen DS, in the exchange. Suitable for hydraulic system LHM + LHS (power steering). The steering unit is built up with newest seals and can be used for LHM + LHS liquid! Or. No. 9D5409726V. Plus 400 Euro Old part deposit. Note: The steering unit must be installed after the Citroen workshop specifications (workshop book 583, book 2, workingpaper D.444-1). You must have the tool 39002 (for the angle position of the steering gear to the steering column). Without this tool, you can not work!

Quality: 3

• Suitable for this article
• Sealing ring (O-ring), for the semi-automatic transmission and above at the steering gear. Suit
  0,75 €
• Rubber seal centrically, for the steering gear. Suitable for Citroen DS. Dimension: 16.5 x 28.5
  3,92 €
• Steering unit - adjusting tool, suitable for Citroen DS. (1955-T). This tool is for the adjustm
  62,38 €

Steering gear repair set for the tie rod guide. Suitable for Citroen 2CV. Consisting of: Pin + seat bowls + guides, ball pin, rubber,

Quality: 3

• Suitable for this article
• Front axle cover sheet. (Cover at the steering gear, below the tie rod securement). Suitable fo
  9,82 €
• Front axle sliding sheet metal at the steering unit. Suitable for Citroen 2CV. Or. No.: AM44279
  7,83 €
• Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suita
  1,55 €

Steering gear repair set. Suitable for hydraulic systems LHM. Suitable for Citroen DS, starting from year of construction 07/1967

Quality: 3

• Suitable for this article
• Steering gear for Citroen DS, in the exchange. Suitable for hydraulic system LHM + LHS (power s
  832,91 €

Steering gear: Pressure spring for the damping pushrod of the steering rack. Diameter: 16.5mm. Or. No. D442-2 + 5411166. Suitable for Citroen DS.

Quality: 3

Steering gear bellow from rubber, suitable for Citroen 11CV + 15CV. Dimension: 58 x 132mm. Or. No. 602135

Quality: 3

• Suitable for this article
• Collars clip strap with lock (made from metal). Overall length: about 500mm. Width: 5,0mm. Thes
  2,53 €

Steering gear bellow from rubber, suitable for Citroen HY.

Quality: 3

• Suitable for this article
• Collars clip strap with lock (made from metal). Overall length: about 500mm. Width: 5,0mm. Thes
  2,53 €

Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. Splines (worm gears) are continuous up to the bearing. Suitable bush = 12233.

Quality: 3

Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. First version. Splines (worm gears) go only up to the half height of the bearing. Shaft diameter at the lower end = 13 mm.

Quality: 3

Steering worm of 8 teeth, inclusive bearing, for Citroen 2CV. Good reproduction! The suitable guide bush down (10mm inside diameter) has our No. 12232. Overall length: 112,8mm.

Quality: 3

• Suitable for this article
• Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF!
  20,73 €

Steering worm of 8 teeth, inclusive bearing, for Citroen 2CV. Inside diameter: 10mm. Suitable lower bush = 12232. Overall length: 112,8mm.

Quality: 4

• Suitable for this article
• Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF!
  20,73 €

Steering worm sealing bellow (angular). Suitable for Citroen DS. Or. No. DS444-12.

Quality: 3

Steering worm distance disk. Suitable for Citroen 2CV. Measurement: 23.5 x 34 x 0,95mm. Or.Nr.: A442-72

Quality: 4

Steering worm bearing bush (down at the needle bearing). Suitable for Citroen 2CV. The bearing is a needle bearing! Only for steering worm with 8 teeth. Inside diameter: 10mm. Outside diameter: 14mm. Overall height: 12mm.

Quality: 2

Steering worm bearing bush (down at the needle bearing). Suitable for Citroen 2CV. The bearing is a needle bearing! Only for steering worms with 8 teeth. Inside diameter: 12mm. Outside diameter: 18mm. Overall height: 12mm. Manufacturer SKF.

Quality: 2

Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF! Inside diameter 10mm, outside diameter 17mm, height of 12mm

Quality: 3

Steering worm bearing bush 2CV, down at the steering worm. (no needle bearing). Inside diameter 10mm, outside diameter 16mm, height of 10mm

Quality: 3

Steering worm locking cap down (the cap is hit from downside into the steering gear). 20mm. Suitable for Citroen 2CV.

Quality: 4

Steering worm nut with sealing ring. Suitable for Citroen 2CV starting from year of construction 03/1971.

Quality: 4

Steering worm nut with sealing ring. Suitable for Citroen 2CV, starting from year of construction 03/1971. From own production, with interchangeable shaft seal. Very significant.

Quality: 3

Steering worm nut shaft seal (as substitute for 12140). Suitable for Citroen 2CV, starting from year of construction 03/1971. Dimension: 19 x 27 x 5mm.

Quality: 3

Steering, repair kit (assembled). Suitable for Citroen 2CV up to Orga No. 2275, Dyane, Mehari. Consisting of the complete guide in the front axle tube, incl. new rack, 24 teeth. Good quality. This is the old version of the steering rack for a steering pinion with 7 teeth!!! Made in Europe

Quality: 3

• Suitable for this article
• Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.
  2,77 €
• Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. Splines (worm gears) are continuo
  39,57 €
• Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suita
  1,55 €
• Screw M7x12, e.g. to fix the steeringwheel 2cv, screw is galvanized
  0,51 €

Steering unit, repair set. Suitable for Citroen 2CV. Consisting of: Guide steering unit pin, 2x slide ring, ring for the gear rack ((27,75mm + - 1/10mm), rubber under the tie rods. Reproduction. Only for LHD, cannot use for RHD.

Quality: 4 360°

• Suitable for this article
• Front axle sliding sheet metal, safety sheet. (Sliding sheet metal on the steering unit). Suita
  1,55 €
• Screw M7x12, e.g. to fix the steeringwheel 2cv, screw is galvanized
  0,51 €

Steering unit - adjusting tool, suitable for Citroen DS. (1955-T). This tool is for the adjustment of the steering column to the steering gear. It is indispensable, for the installation of a new steering unit!

Quality: 3

Steering sleeve for CX from 1980 on, suitable for left and right side.

Quality: 4

Collar steering gear, per piece. Very good reproduction. Suitable for Citroen DS. Or. No. D44220

Quality: 1

Collar steering gear. Suitable for Renault R8, Alpine, Simca 1000. Matra Djet. Assembly diameter about 40mm + 10mm. Or. No. 7700653459

Quality: 3

Collar steering gear. Per piece. Suitable for Citroen DS.

Quality: 4

Hub nut for the lower steering unit pin. Suitable for Citroen 11CV + 15CV. Thread: M34 x 150. Or. No. 601877

Quality: 3 360°