CO adjusting screw, M 5x0,75 mm, (idle mixture adjusting screw), for Solex carburetor. Suitable for
Citroen 2CV (round carburetor). Citroen 11CV, HY, DS. Renault 4CV, Dauphine, R4, Caravelle, Floride. Peugeot 203, 403, 404, 504.
carburetor and carburetor gasket sets for Peugeot DS
All fuel-controlling spare parts from us, are not applicable for fuel with an ethanol content of more than 5%. The warranty is not valid if high ethanol content such as E10 or greater is being used. Damages like swelling, dissolving or decay are a sign of using too much ethanol. Unfortunately, the developers of modern fuel are considering the impact on our cherished properties ever less.
54 Articles | Page 1 of 2
CO tester (exhaust tester). Digitally. Optimally for the experienced mechanician, in order to
adjust the carburetor. We use it since years for our classic cars! English operating instructions are attached. For the language German, Dutch, Spanish, Italian, French can be down-load the operating instructions of our homepage.
PDF FILE Nozzle gauge from 0.45 to 1.5 mm. 20 nozzle gauges. With these nozzle gauges, you can determine the
diameter of carburettor nozzles. Indispensable for work on the carburettor (e.g. changing the nozzle to original values, calibrating the carburettor, etc.).
Injection pressure regulator, suitable for Citroen DS IE. Very good reproduction "Made in Germany
This controller corresponds to the Bosch number 0280 160 007 / 0 280 160 003 / 0 280 160 004. Citroen Or. No. 1D 5412357T
Fuel injection system, temperature sensor at the cylinder head (coolant sensor). Suitable for
Citroen DS IE. Replacement product from Hella. The plug must be converted!
Fuel injection nozzle rubber above (large rubber), suitable for Citroen DS21IE + DS23IE. Dimension
21.8 x 32.2 x 7,6mm. Or.Nr.: 5412354K
Fuel injection nozzle rubber down (small rubber), suitable for Citroen DS21 IE + DS23 IE
Dimension: 7.4 x 14.6 x 4,5mm. Or. No. DX144101A
Rubber ring (seal) between air filter and carburetor. Suitable for Citroen DS, old version
Dimension: 65 x 71 x 90 x 20mm. Or. No. DS142-106
Fixture for the throttle valve case (silent rubber). Suitable for Citroen DS IE. Diameter: 30mm
Height: 16mm. Or. No. DX142378A
Crank case (engine block) air vent hose above. Connection to the air intake hose between carburetor
air filter. Suitable for Citroen DS with carburetor engine. Inside diameter: 15 + 17mm. Or. No. 5413610M.
Crank case (engine block) air vent hose down. Suitable for Citroen DS, to year of construction
07/1972 (carburetor engine). Diameter: Both sides 19-20mm. Length: 230mm (shorten if necessary). Or. No. DX13276C, DY13276A, DX132-76A
Idle stabilization completely, in the exchange. Idle stabilization does not have a vent screw
Suitable for Citroen DS IE (injection engine). Or. No. DXN142-020. Plus Old part deposit 150 Euro.
Idle stabilization completely, in the exchange. Idle stabilization does not have a vent screw
Suitable for Citroen DS carburetor. Or. No. Dx142-020. Plus Old part deposit 150 Euro.
Air intake hose (connecting hose), from the air filter to the throttle valve. Suitable for Citroen
DS IE (injection engine), all years of manufacturing (without air condition). Diameter: 66mm. Length: 550mm. Or. No. DX171241A
Air intake hose (connecting hose), from the air filter to the throttle valve. Suitable for Citroen
DS IE (injection engine), with air conditioning. Diameter: 66mm. Length: 730mm. Or. No. DX171206A
Air intake hose, between carburetor (Weber) and air filter. Suitable for Citroen DS, with the
following factory codes: DX, DJ, DJF, DY, DLF, DT, to year of construction 07/1972. Inside diameter carburetor-laterally: 69mm. Length about: 180mm. Or. No. DX1713
Air intake hose, between carburetor and air filter (Solex). Suitable for Citroen DS (with Solex
carburetor). Length about: 215mm. Inside diameter carburetor-laterally: 50mm. Or. No. DX171-3B
Air intake hose, between carburettor and air filter. Suitable for Citroen DS, from year of
construction 1957 to 1964. length approx.: 310mm. Inner diameter carburettor side: 50mm. Or. No. DM171-3
Air hose set (4 item) for engine warming up regulation. Suitable for Citroen DS IE. Or. No
DX144-214A + DX144-215A + DX144-216A + DX144-217A
Engine exhausting hose, at the throttle valve holder. 90° bent. Inside diameter: 16,50mm. Suitable
for Citroen DS IE. Or. No. DX132-281A
Vacuum hose (1030mm), before the throttle valve (connection from the rear) and 3 path connector for
auxiliary air slide valve. Suitable for Citroen DS IE. Inside diameter: 11,0mm. Length: 1030mm. Or. No. 2D5411135K
Vacuum hose, behind the throttle valve (Connection laterally) and 3 way connector for auxiliary air
slide valve. Suitable for Citroen DS IE. Inside diameter: 11,0mm. Length: 608mm. Or. No. DX144-218A
Vacuum hose for the full load switch. Suitable for Citroen DS IE (injection engine). Outside
diameter: 10mm. Inside diameter short side: about 4mm. Inside diameter long side: about 5,5mm. Or. No. DX144243A
Vacuum hose, between throttle valve case and pressure sensor. Suitable for Citroen DS IE. Inside
diameter: 7,0mm. Or. No. DX144-226A
Connection rubber for the intake manifold. Suitable for DS IE (injection engine). Outside diameter
59mm. Height: 45mm. Per piece. Or. No. DX141117A
Carburetor sealing set, for Solex PBICA. Suitable for Citroen 2CV, DS, 11CV, HY. Peugeot 403, 404
504 L, J7. Renault Dauphine + Floride. The diaphragm has a diameter of 20mm.
Carburetor, Solex 34 PBIC. Reproduction. Suitable for Citroen ID + DS, Installed of year of
construction 1965 to 1968.
Carburetor sealing set small, Solex PBICA. Suitable for Peugeot 203, 403, 404. Citroen 11CV, HY, DS
(early years of construction).
Carburetor sealing set, for Solex carburetor 28/36 SFIF. Suitable for Citroen ID19, DS20, DS21. The
carburetor sealing set are supplied inclusive diaphragm + float needle valve.
Carburetor sealing set, for Solex carburetor 32SDID. Suitable for Citroen ID19. The carburetor
sealing set are supplied inclusive. Diaphragm + float needle valve.
Carburetor sealing set, for Weber 24/32DDC + 23/32DDC. Suitable for Citroen DS19. The carburetor
sealing set are supplied inclusive float needle valve.
Carburetor sealing set, for Weber 28/36 DDE + DLE. Suitable for Citroen DS. The carburetor sealing
set are supplied inclusive float needle valve.
Carburetor sealing set, for Weber 28/36 DM + DMA. Suitable for Citroen DS, starting from year of
construction 09/1972. The carburetor sealing set are supplied inclusive float needle valve.
Carburettor jet cleaning tool. Essential for carburettor maintenance and cleaning in your classic
car. The scope of delivery includes five stainless steel nylon brushes with diameters of 2, 3, 4, 5 and 7 mm and a brush length of 30 mm. Ten stainless steel cleaning needles with diameters of 0.7, 0.9, 1.1, 1.3 and 1.4 mm. A 4 mm Allen key and twelve round carbon steel files with diameters of 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1.0, 1.1, 1.2, 1.3, 1.4 and 1.6 mm. A flat file is also included.
Seal under carburetor oval (2 fittings). Suitable for Citroen ID19, HY, 11CV. Peugeot. Inside
diameter: 34mm. Spacer bolt center to spacer bolt center: about 61mm. Or. No. 481717. This seal fits almost to all Solex 34 carburetors.
Seal under carburetor (insulating plate), between that intake manifold and the carburetor. Suitable
for Citroen DS, starting from year of construction 1965. Or. No. 1D5440931E
Preheating hose for the intake manifold (carburetor preliminary heating). Inside diameter: 19/24mm
Suitable for Citroen DS, to year of construction 07/1972 (Solex carburator). Engine: DV. Or. No. DV235-35A
Preheating hose for that intake manifold (carburetor preliminary heating). Suitable for Citroen DS
19 semi-automatic transmission, of year of construction 1966 to 1968. Inside diameter: 16,0mm + 19,0mm. Or. No. DY235-140A
Preheating hose for that intake manifold (carburetor preliminary heating). Suitable for Citroen DS
starting from year of construction 07/1972. Or. No. DX235-140A.
Preheating hose for the intake manifold (carburetor preliminary heating). Suitable for Citroen DS
to year of construction 09/1960. Inside diameter both sides: about 18,0mm. Overall length about: 270,0mm. Or. No. DS142-125A
Preheating hose for the intake manifold (carburetor preliminary heating). Suitable for Citroen DS
of year of construction 09/1960 to 1965. Diameter: 15-16mm. Or. No. DF14225
Preheating hose for the intake manifold (carburetor preliminary heating). Suitable for Citroen DS
of year of construction 1960 to 1965. Inside diameter both sides: about 21,0mm. Overall length about: 270,0mm.
Preheating hose for the intake manifold (carburetor preliminary heating). Suitable for Citroen
ID19, of year of construction 1966 to 1969. Inside diameter both sides: about 18 - 19mm. Overall length: about 325mm. Or. No. DV235-35
Preheating hose for the auxiliary air slide valve. Connection at the water pump, on the left at the
engine. Suitable for Citroen DS 21 IE, DS 23 IE. Connections both sides: 19 - 20,0mm. Or. No. DX235-135A
Warning switch at the auxiliary air slide valve (for the thermometer), suitable for Citroen DS IE
starting from year of construction 7/1972. Thread: M16. Or.Nr.5428845K
54 Articles | Page 1 of 2
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
