for Peugeot J5

End cap rubber. 14mm inside diameter. E.G., for plugging water pumps or heater radiator connections.

• Suitable for this article
• 
  hose clamp for 15-20mm.
  0,93 €

End cap rubber. 16mm inside diameter. E.G., for plugging water pumps or heater radiator connections.

End cap rubber. 18mm inside diameter. E.G., for plugging water pumps or heater radiator connections.

End cap rubber. 21mm inside diameter. E.G., for plugging water pumps or heater radiator connections.

End cap rubber. 23mm inside diameter. E.G., for plugging water pumps or heater radiator connections.

End cap rubber. 26mm inside diameter. E.G., for plugging water pumps or heater radiator connections.

End cap rubber. 8mm inside diameter. E.G., for plugging water pumps or heater radiator connections.

Hazard warning lights switch 12 Volt! Manufacturer Bosch! The hazard flasher system uses the

existing flasher relay and is relatively easy to install. Attention: a suitable bulb must be ordered separately. Our article number 14425.

• Suitable for this article

Ignition cable set. Suitable for 404 (1,6L) all model`s. Peugeot 504 (1,8L + Injection). 504 Pick

UP (1,6). J7 (1,6L + 1,8L). Citroen C25 (2,0E). Cable length: 350, 550, 626 + 800mm. Cable to the ignition coil: 520mm. Made in Europe.

• Suitable for this article
• 
  Spark Indicator. This non-contact spark tester will test for the presence of
  17,76 €
• 
  Spark plug electrodes extension. Suitable for Peugeot 403, 404, 504, J7
  5,31 €
• 
  Spark plug isolation pipe. Suitable for Peugeot 203, 403, 404, 504. Original
  4,91 €
• 
  Spark plug electrode extension. Length: 87mm. Suitable for Peugeot 203, 403
  5,15 €

Spark gap measurement (testing) tool. With the help of this small, inexpensive tool, the spark gap

of the spark plug can be checked very easily and safely. So, if the engine does not start: Is the spark plug sparking at all! And if so, how strong! Then exclusion procedure: Ignition OK? It is not getting any petrol!

Flexible Spark Plug Remover/Installer. This specially designed tool allows access to spark plugs

where they are deep seated or require off-line access. The tool is also designed to grip the spark plug securely allowing the removal with ease.

Tap drill M14x1,25. (Spark plug threads).

• Suitable for this article

Heli coil spark plug thread repair set. For all M14 spark plugs. Contents: 1 bore + cutting tool

installation spindle. 10x heli coil insert M14x1,25x17,5. (Spark plugs with long threads). 10x heli coil insert M14x1,25x12,7. (Spark plugs with short threads, 2CV, R4).

Spark plug thread Helicoil insert. M14x1,25x12,7 (spark plugs with short thread 2CV, R4). Refill

package (10 pieces)!

Peugeot spark plug connector. Suitable for Peugeot 404, 504, J7. Or. No. 5964.06. Total length: 150

mm. Diameter: 21 mm.

Ignition module 7 pin. Used with BX, AX, CX, VISA, C15, ZX, C25. Peugeot 104, 205, 305, 309, 504

505, J5.

Starter lock reproduction. Suitable for Peugeot 204, of year of construction 05/1969 to 1977. 304

from 03/1970 to 1977. Peugeot 404, 504 + J7

Ignition coil with pre-resistor. 12 V. Brand manufacturer! Suitable for Citroen DS, CX, GS, AMI8

Super. Peugeot 403, 404, 504, 505. Renault R4, R5, R12, R16 etc.

Ignition coil 12 V, without pre-resistor. Suitable for Citroen DS, GS, HY. Peugeot 203, 204, 304

403, 404, 504, J7. Renault R4, R5, R16 etc.. Original VALEO

Spark Indicator. This non-contact spark tester will test for the presence of power in spark plugs

coils and distributors. Simply place the grooved end over the spark plug wire with the engine running and the high intensy bulb will flash indicating spark. Note: Depending upon screen of the ignition cables, it can be possible, that you see the flashing by daylight, very bad!

Brake cylinder hone. For use with a cordless drill to clean brake cylinders during service

22-69mm. For honing out brake cylinders. For use with a standard drill.

• Suitable for this article
• 
  Hone segment 30x4mm (2 fittings) for brake cylinder hone 20916.
  9,27 €

Engine cylinder hone. Enables the inside surface of the cylinders to be cleaned of carbon deposits

etc. Suitable for all cylinders with a bore diameter of 50

• Suitable for this article
• 
  Hone segment 100x10mm (3 fittings) for engine cylinder hone 20918.
  20,81 €

Cylinder head gasket set for Indenor Diesel. For engine: TMD85, XDP85, TMD85-AD, XPD (1816cc)

Suitable for Citroen HY Diesel. Peugeot 403 Diesel, 404 Diesel, 504 Diesel, J7 Diesel. Heavy one: 1,25mm. Or. No. 0199.48

Cylinder head screws set CX Diesel + turbo-Diesel, C25 Diesel 2.5, Peugeot J5 2.5 Diesel + TD. M12

outer hexagonal. Or. No. 020441 (8x) + 020442 (9x).