steering rods for Renault 2CValt

Trakrite Wheel Alignment Gauge. Trakrite is the simplest, most accurate device for checking the

alignment of the steered wheels of car and light commercials. It is a roller bearing platform over which one front wheel is slowly driven with the wheels in their straight ahead position.

Tie rod, clip for the adjusting sleeve. Suitable for Citroen 2CV.

• Suitable for this article
• 
  Tie rod: M7 screw for the clip of the tie rod. Suitable for Citroen 2CV.
  0,56 €
• 
  Self-locking nut M7
  0,44 €

Tie rod, on the left of or on the right fitting. 451,6mm lengthens. Only suitable for Citroen 2CV

to year of construction 1973. Or. No. AM443-1. Note: After the year of construction 1973 the tie rods had a length of 497mm! Reproduction, without tie rod end. Thread: M14x1,25 right-hand thread

• Suitable for this article
• 
  Tie rods adjusting sleeve. Suitable for Citroen 2CV. (Coupling sleeve for tie
  14,78 €
• 
  Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.
  2,77 €
• 
  Tie rod nut, self locking. For the securement at the steering gear. Suitable
  0,58 €
• 
  Tie rod, clip for the adjusting sleeve. Suitable for Citroen 2CV.
  3,18 €
• 
  Tie rod: M7 screw for the clip of the tie rod. Suitable for Citroen 2CV.
  0,56 €
• 
  Self-locking nut M7
  0,44 €

Tie rod: M7 screw for the clip of the tie rod. Suitable for Citroen 2CV.

• Suitable for this article
• 
  Self-locking nut M7
  0,44 €

Tie rods adjusting sleeve. Suitable for Citroen 2CV. (Coupling sleeve for tie rod with tie rod

end). Thread: M14x1,25

• Suitable for this article
• 
  Tie rod, clip for the adjusting sleeve. Suitable for Citroen 2CV.
  3,18 €
• 
  Tie rod: M7 screw for the clip of the tie rod. Suitable for Citroen 2CV.
  0,56 €

Tie rods rubber, at the front axle. Suitable for Citroen 2CV4 + 2CV6.

Tie rod nut, self locking. For the securement at the steering gear. Suitable for all Citroen 2CV

Dyane, Ami.

Tie rod lever fixing bolt. Suitable for Citroen 2CV. Dimension: M7 x 27,5mm. Tensile strength: 10.9

Tie rod lever on the left, suitable for Citroen 2CV to year of construction 1963. Reproduction.

Tie rod lever on the right, suitable for Citroen 2CV to year of construction 1963. Reproduction.

Tie rod lever safety sheet (without gradation). Suitable for Citroen 2CV from the fifties. Or.Nr

451402

Split pin small, for the tie rod end nut + radius arm bearing. Suitable for Citroen 2CV

Measurement: 2 x 20mm

Tie rod end wrench (630-16/2), for the nut in the tie rod end. Suitable for Citroen 2CV. Note: this

tool do not fit for tie rod end with strengthened nuts.

• Suitable for this article
• 
  Tie rod end locking nut. Suitable for Citroen 2CV. Reproduction
  2,59 €
• 
  Tie rod end repair set on the left. Inclusive bearing pan, pressure spring
  64,36 €
• 
  Tie rod end repair set on the right. Inclusive bearing pan, pressure spring
  64,36 €
• 
  Tie rod end, 2 x seat bowl + 1 x pressure spring + 1 x crown nut. Complete
  12,79 €

Tie rod end locking nut. Suitable for Citroen 2CV. Reproduction

• Suitable for this article
• 
  Tie rod end wrench (630-16/2), for the nut in the tie rod end. Suitable for
  16,76 €

Tie rod end, 2 x seat bowl + 1 x pressure spring + 1 x crown nut. Complete repair set, in order to

repair the tie rod end inside. High quality. Suitable for all Citroen 2CV, AK, Dyane, AMI.

• Suitable for this article
• 
  Tie rod locking plate, suitable for Citroen 2CV. For tie rod lever with stepped
  1,87 €
• 
  Tie rod end wrench (630-16/2), for the nut in the tie rod end. Suitable for
  16,76 €

Spring in the tie rod end. Suitable for Citroen 2CV. Per side 1x spring is required.

• Suitable for this article

Tie rod end collar "Made in European Union", suitable for Citroen 2CV, Mehari, Dyane, AMI. This

collar is produced in Europe for "Der Franzose". The collar is very flexible and can be mounted over the complete tie rod end, without it tears. Better than original!

Tie rod end collar, suitable for Citroen 2CV, Dyane, AK, Ami. Good reproduction. Or.Nr.: A44313B