Rubber stop round (conically), for the rear axle. Suitable for Citroen DS + SM. Citroen HY
Dimension: about 46,5x34mm. Or. No. 1D5404572Y
for Sonstige-Citroen SM
922 Articles | Page 6 of 19
Rubber seal profile (by meters), for nearly all older Citroen, 2CV, HY, DS. (Door + luggage
compartment seals)! Made in Germany! Quality: EPDM 317. Easily rubbed in with talcum powder. Wide one: 25,5mm
Rubber cap for the connection at the generator. (Protecting cap). This cap should never be missing
Universal fitting! For max. cable diameters: 7,62mm. Inside diameter 12,7mm.
Rubber cap for the connection to the starter motor. (Protecting cap). This cap should never be
missing. Universal fitting! For max. cable diameters: 17,8mm. Inside diameter 22mm.
Retaining clip emblems for Citroen, Renault, Peugeot, old models. 2.5mm inner diameter (i.e. for
2.5mm pins on the emblems). Length: 7.5mm. Per piece
Fixing clip, for the hydraulic line (6,35mm) between hydraulic pump and pressure controller
Suitable for Citroen DS.
Thread Repair Kit M7x1, for repairing damaged threads. For plating threads in materials with low
shearing strength 1 twist drill, 1 tap, 1 installation tool, 1 tang breaker, 25 x M7x1 coil.
Helicoil repair set for M7. Consisting of: Twist drill (to M12), hand taps from HSS, mounting
spindle, insertion pin breaker (to M12). In each case, 10 theaded inserts M7 in the lengths: 7,0mm, 10,5mm, 14,0mm. Original Helicoil, no reproduction.
Inside roof lining adhesive from Teroson. Contents: 680g. Light, transparent adhesive material for
the roof and door linings.
Horn (12 V), completely with air compressor + 2 x compressed air horn, relay and air hoses. 750 +
800Hz (2 different tones). 115dB (A). Length of the air horns: 210 + 165mm. Length of the air compressor: about 105mm.
Horn (trumpet) 12 V, high tone. 480Hz, 108dB (A). Very high quality horn, made in the European
Union. The horn is made of metal, with a red cover (trumpet) from plastic! Universal fitting. Diameter: about 110mm. ECE checked.
PDF FILE Horn (trumpet) 12 V, deep tone. 420Hz, 108dB (A). Very high-quality horn, made in the European
Union. The horn is made of metal, with a red cover (trumpet) from red synthetic! Universal fitting. Diameter: about 110mm. ECE checked.
Horn 12 V, high tone. 430Hz, 114dB (A). Very high quality horn, made in the European Union. The
horn is from the front in red painted! Universal fitting. Diameter: about 91mm. Metal housing. ECE checked.
Horn 12 V, deep tone. 340Hz, 114dB (A). Very high quality horn, made in the European Union. The
horn is from the front in red painted! Universal fitting. Diameter: about 91mm. Metal housing. ECE checked.
Horn set (2 pieces) chrom-plated, from Bosch. Frequencies: 325 and 400 Hertz. Volume: 118 db(A)
operating voltage: 12 V, power consumption: 48 W each, diameter: 156 mm, depth: 91 mm, EMV protection: included. Universal fitting.
Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach
Suitable for 4,5mm line.
Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach
Suitable for 6,35mm line.
Hydraulic + brake pipe handle made of metal. The fixture has a rubber lining and is to attach
Suitable for 8,0mm line.
Hydraulic fluid return pipe (leakage oil line). Material: Rilsan. Dimension: 2x4mm. Suitable for
Citroen DS. By meters. Customer cut - return not possible!
Brake hose seal + hydraulic line seal (socket) green. For LHM (hydraulic fluid green), 4,5mm line
(connector 9mm). Suitable for Citroen DS, HY with hydraulics, GS, CX etc.
Hydraulic line + brake hose seal (socket) green. For LHM (green hydraulic fluid), 4,5mm line
(connector 9mm). Very good reproduction. Suitable for Citroen DS, HY with hydraulic, GS, CX etc.
Brake line flaring tool, for brake and hydraulic lines. Particularly for Citroen connectors. With
thrust pieces for 3,5mm + 4,5mm lines (8,0mm + 9,0mm Clinch screws).
Hydraulic line and Brake line flaring tool for use at the vehicle! For all lines with 3,5mm, 4,5mm
6,35mm (1/4 "). (Citroen)
Hydraulic line Brake line flaring tools for use at the vehicle (to use at the car). For all
flanging! For all Citroen lines with 3,5mm, 4,5mm + 6,35mm (1/4 "). For all lines after DIN/CSAE, for flanges of the types CD, E, F, F180 in the usual quantities 4,75mm, 6mm, 8mm, 9mm and 10mm.
Hydraulic line seal 6,35mm, for LHM (green) hydraulic system. 10mm outside diameter! About 10mm
long. Suitable for Citroen DS, CX, GS, SM, BX, XM etc.
922 Articles | Page 6 of 19
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
