Taillight + stop light, round, (2 thread light). 70mm diameter. Suitable for Citroen AK 400, DS
BREAK, HY, Mehari. Version AXO! (suitable bulb: Item 14037). (Reproduction, without "E" test mark)
BREAK, HY, Mehari. Version AXO! (suitable bulb: Item 14037). (Reproduction, without "E" test mark)
HY, Mehari, AMI6. Wide light collar. Outside diameter 71mm, mounting holes center to center about 55mm, collar level from the inside measured: 14,5mm. We could buy up some thousand caps. No reproduction (NOS).
BREAK. HY, Mehari. Narrow light collar. Outside diameter 68mm. Mounting holes center to center about 58mm. Collar level from the inside measured: 10,0mm. We could buy up some thousand caps. No reproduction (NOS).
Y, Mehari, AMI6. AK544262A, for manufacturer Seima
were used in many French cars!
classic cars. Diameter: 56mm.
73 x 11mm. Or. No. 440531. Per piece
markings! Optically like original! Made in Germany.
markings! Optically like original! Made in Germany.
for Citroen 2CV, DS, HY, SM, GS, CX, Peugeot
button and not a toggle switch. The push button is useful for electric windscreen washers, horns or headlight flashers, for example. Dimensions: 36x18mm (French standard size). Suitable for Peugeot, Citroen, Renault.
switch for e.g. heater blowers, additional consumers.... Dimensions: 36x18mm (French standard size). Suitable for Peugeot, Citroen, Renault.
over the sheet metal fold. Very helpful!
brackets in different widths so that narrow and wide piping can be fitted (e.g. for the 2CV, R4....). Suitable for tool with item number 20134.
rubber lip (seal) inclination (spread) and it can fit the sealing trim at the same time. Attention: The tool is for very wide piping. For chrome piping e.g. Citroen 2CV, Renault R4 etc. small brackets must be fitted. See our item number 20137.
rubber-mounted front, rear and side windows. Very stable, water resistant, remains elastic. Good adhesion even on damp windscreens.
to sealing rubber-mounted front. - Tail and side windows. Very stably, water-resistant, remains elastic. Good adhesion also on wet disk.
with velvet). Suitable for Citroen HY, starting from year of construction 01/1968. Or. No. HY961-51A
reservoir is supplied with mounting and accessories and can be installed in any vehicle, e.g. Citroen Mehari, Renault R4 first versions, etc. This type of windscreen washer reservoir has also been installed in many Italian vehicles (Alfa Romeo Spider...).
h push-button, cable, cross bars etc. very practical and small. Width 19,5cm, height of 16,5cm, depth 5,5cm
overall height totally: 185mm. Building depth altogether: 100mm. The reservoir is supplied with fixture. The fixture is from the rear at the reservoir.
etc. dimension: 5 x 18 x 4mm.
the original! Mounting diameter: 8,0mm.
screwed with a nut from behind. 2x water jet. Flat design.. Mounting diameter: 8,0mm.
S (DS Installed to year of construction 1969!). M 7x1mm
Citroen DS, to year of construction 1969. In addition, this additional connection is very practical for Citroen DS, HY etc.. Mounting hole: 7,0mm.
connection from above! Made in the European Union. The picture indicates the correct mounting position. The pump section is down, the electric motor above!
well for conversion, e.g. 2CV, Dyane, Peugeot, Renault. Note: The pump is not self-priming. The water must run (from alone) inside. Outlet water = power connection side. If the pump works more than 15 seconds without water, it is broken.
stoppers, 1x T-valve, 3 meters hose. Assembly: Starting from the foot pump with the T-valve, 1x to the reservoir (place the valve in such a way that the water from the reservoir can pass through) and 1x to the windshield washer nozzle (valve lets the water pass in the direction of the nozzle). The flow directions are marked with an arrow on the valve. Assembly instruction online in the shop.
addition, the pump is a reproduction of the first version, and can installed into a Citroen 2CV6 and partial in a Renault R4 .
dashboard. The pump corresponds to the original hand pump as it was mounted in the 2CV6 until the year of construction 1990. Or. No. AZ864-209A. This pump was also installed in the Citroen ID19 until the year of construction 1962 (DM564-9) and the Citroen HY. Please note: The pump has 3 connections: 1x inlet and 2x outlet. For the 2CV with the enclosed T-connector, please bridge 1x (see photo 2 in the shop).
mounting! Suitable for Citroen 2CV. In addition, the pump can be universal installed.
2CV4, Citroen HY. Consisting of lever, spring, mounting plate.
form, plastic case chrom-plated. Installed until 1990! Without bulbs.
e chrom-plated, like in the final years of construction installed. (up to year of construction 1990)! Original supplier Vaöeo, no reproduction. Without bulbs. Production is stopped by Valeo! We took over the final 1800 headlamps from Valeo.