for Peugeot ACDY
1677 Articles | Page 31 of 34
Identification plate green, for Citroen. 78x40mm. 2 bores. (Metal). The green identification plates
were often used for gearbox identification!
Identification plate orange, for Citroen. 78x40mm. 2 bores. (Metal). The red identification plates
were often used for engine numbers!
Identification plate S.A.A Citroen. These identification plates are installed in 2CV, DS, 11CV, HY
Measurements of 43x70mm. Unfortunately a bad reproduction.
Identification plate, original-faithful reproduction. Suitable for Citroen 2CV, DS, HY, 11CV
Measurements: 43 x 78mm.
Transfer pump metal version, inclusive 2 hoses for drawing in and running off, 500ccm. Applicable
e for: Diesel, fuel oil, coolant, brake fluid.
PDF FILE Console for a radio in DIN measurements. The console is mounted under the dashboard. Uinversal
fitting, e.g. Citroen 2CV, DS. Dimension cutout for radio: 182 x 53mm. Dimension outside: Height: 76mm. Wide above 250mm (down 220mm). Deep one: 175mm.
Under cover from strengthened plastic fabric (for the seat + backrest). Suitable for Citroen 2CV
This cover is mounted instead of the jute covers.
Undercover made of reinforced plastic fabric - seat bench front or rear (for the seat + backrest)
Suitable for Citroen 2CV. This cover is fitted instead of the jute covers. The plastic fabric is much more durable.
Vacuum diaphragm, pulldown, for the Choke (cold engine starting). Suitable for Citroen 2CV6. The
diaphragm is mounted at the carburetor above. Or. No.: 95568478
Protection plate for the engine, for the original chassis. Suitable for Citroen 2CV, AK400, Mehari
This extremely heavy sheet metal is an accurate reproduction of the original protection plate, which was offered by Citroen. Made in Germany.
USB A+C adapter (12 volt) for cigarette lighter. The adapter has 2 connections. 1x USB-A (the large
wide plug) and 1x UBB-C (the new small plugs).
Valve clearance adjustment screw, suitable for Citroen 2CV6 + 4. Measurement: 7x17,5mm, overall
ll length 25mm. Or.Nr. A124-4
Valve (rubber valve) for rim. Suitable for Citroen 2CV, DS, CX, HY, GS. Renault R4, R5, R6, R8
R10, rear engine. Peugeot 203, 403, 404, 504, 604, 204, 304, J7. For valve hole: 11,3mm. Length: 42,5mm.
Valve long (rubber valve) for rim. To uses this long valve, if the rim has a large wheel cover
(with cutout for the valve). Suitable for Citroen DS, CX, HY, GS. Renault R4, R5, R6, R8, R10, rear engine. Peugeot 203, 403, 404, 504, 604, 204, 304, J7. For valve hole: 11,3mm. Length: 61,5mm.
Valve cap reproduction, galvanizes, for Citroen 2CV4 + 2CV6. Or.Nr. 75478957. The valve cap is
tightened frequently too strongly, and licks then oil.
2CV starting from 1971, stud bolt M7x76mm, for the mounting the valve cap on the cylinder head
Suitable for Citroen 2CV starting from year of construction 1971.
2CV until 1971, stud bolt M7x83,5mm, for the mounting the valve cap on the cylinder head! Suitable
for Citroen 2CV to year of construction 1971.
VIDEO Special valve cover gasket. Suitable for Citroen 2CV6, Dyane 6, AK400, Mehari, AMI8. Made from
silicone. The valve cover gasket fits around the edge of the valve cover. This makes installation much easier.
Valve grinding-in paste (engine valves in the cylinder head), 100ml box. The double box contains
pre-grinding paste (rough) and regrinding paste (fine).
- Suitable for this article
valve spring inside (small spring), for inlet + exhaust valve Citroen 2CV6 + 2CV4. Outside
diameter: 22,5mm. Height: 31,5mm. Or.Nr. AM124-9A
Valve guide inlet valve for Citroen 2CV6. Length: 47mm, outside diameter 12,5mm, inside diameter
8,00mm, fit above 10,5/11mm.
Valve spring cotter for Citroen 2CV6, final version. The valve stem has 3 grooves. Suitable for
inlet + exhaust valve. You need 2 pieces per ventil.
Valve stem seal inlet, for AMI6, 2CV4. Inside diameter 7,8mm, outside diameter 9,9mm-13,2mm
strength 10mm. Per piece!
Carburetor sealing set (only seals), inclusive Seal under carburetor, for oval carburetor SOLEX
26/28/35 CSIC, SCIC. Suitable for Citroen 2CV starting from year of construction 1981, Dyane, AMI. Made in Germany.
Carburetor setting gauge. For the height adjustmenting from the carburetor float. Suitable for
Citroen 2CV6, Dyane 6, Mehari. For oval carburetor Solex 26/35. Made in Germany.
Carburettor oval (new part), for Citroen 2CV6, Solex 26/35. All carburettors are disassembled by
us, and the float level (float gauge) is adjusted. The carburetor is then mounted on a 2CV 6 engine and subjected to a test run. We then adjust the carburetor completely according to Citroen specifications. The carburettor is therefore ready for installation and requires only a minimum of adjustment to your engine. The workload of around 1.5 hours is already included in the sales price.
1677 Articles | Page 31 of 34
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
