crankshaft-camshaft-piston-flywheel for Peugeot AK-AZU
42 Articles
Piston + liner (2 pieces) for Citroen 2CV4, (425ccm). Citroen AZL, AZU, Dyane (425cc). Inclusive
piston rings. 66mm bore. Liner fit measurement in the engine block 80 mm . Suitable for 16/18HP + 12 HP (the pistons are curved, this is not original for a 12HP engine). Diameter piston pin: 20,0mm.
Piston + liners for 2CV4, 435cc, inclusive piston rings + piston pins. Bore: 68,5mm. Piston pin: 20
x 58,3mm. Piston rings: 1,75 + 2.0 + 4,0. Original supplier.
Piston + liner (2 pieces). Suitable for Citroen 2CV6/Club, Charleston, Special. Dyane 6, Ami 6 + 8
Engine capacity: 602ccm. Engine: M28, R6, 627. Compression 8,5:1. Inclusive Piston rings. Piston pin: 20 x 63,5mm. High-quality reproduction from the European Union.
Piston + liner (2 pieces). Suitable for Citroen 2CV6/Club, Charleston, Special. Dyane 6, Ami 6 + 8
Engine capacity: 602ccm. Engine: M28, R6, 627. Compression 9:1 (32HP). Inclusive Piston rings. Piston pin: 20 x 63,5mm. High-quality reproduction from the European Union.
Piston rings for Citroen 2CV4, 68,5mm bore, 435ccm. (1 set for 2 pistons). Label manufacturer
Measurements: 1,75 + 2.0 + 4,0mm. Engine A79/1, AYA2
Piston rings for Citroen 2CV6 starting from year of construction 1976. (1 set for 2 pistons)
Reproduction. Measurements: 1,75 + 2.0 + 3,5mm. Or.Nr.: 5503402.
Piston rings, for 2 pistons, original, 602cc engine as from 1976. Measure: 1,75 + 2,0 + 3,5mm. 74mm
m bore. Improved version with 2 steel rings! The benefits are: Higher running performance, resistant, improves adaptation to the liner, less friction, reduction of the oil consumption!
Piston rings for Citroen 2CV6 to year of construction 1976. (1 set for 2 pistons). Bore 74mm. Label
manufacturer! Measurements: 1,5 + 2.0 + 4,0mm
Crankshaft for 2CV6. New part. We only import the crankshafts from South America, which are made on
the original tools and with the original materials (this factory produce the 2CV for the South American market). Attention, there are also cheaper crankshafts from China, but we do not offer them for quality reasons.
Crankshaft gear wheel narrowly, for Citroen AMI8 + 2CV6. 22 teeth. Gear-wide: 13,6mm. Wide one
completely: 15,6mm.
- Suitable for this article
Engine repair kit (new parts only). Suitable for Citroen 2CV6, Dyane6, Mehari. Consisting of 2x
pistons + liners with compression ratio 8.5:1. New cylinder head left + right (incl. valves and rocker arms). Engine gasket set with oil seals, oil filler neck, oil filter. The crankshaft and camshaft are overdimensioned and can normally be used for a running performance of 500,000 km without any problems.
Engine repair kit (new parts only). Suitable for Citroen 2CV6, Dyane6, Mehari. Consisting of 2x
pistons + liners with compression ratio 9:1. New cylinder head left + right (incl. valves and rocker arms). Engine gasket set with oil seals, oil filler neck, oil filter. The crankshaft and camshaft are overdimensioned and can normally be used for a running performance of 500,000 km without any problems.
Camshaft spring. The spring is mounted in the camshaft drive gear (camshaft gear). The springs
compensate the tooth flank play! Suitable for Citroen 2CV6, AK, ACDY, Dyane, Mehari, AMI. Or. No. A122-98. Diameter: 10.5mm. Length: 21mm.
Camshaft completely with bearings. Suitable Citroen for 2CV6. Original Citroen, no reproduction! We
could find a stock, with supported over 400 original camshafts. These are now in our existence.
Oil cooler hollow screw - banjo screw (screw connection - oil cooler connection in the engine
block). Suitable for Citroen 2CV4 (16 PS) with 425ccm (26.5 cubic inches) engine. Or. No. A225-91. Dimensions: M14x1,5. Length: 44mm
Connecting rod bush for Citroen 2CV (not suitable for 2CV6). Inside diameter: 19,5mm, outside
diameter: 22,1mm, height length: 25mm
Flywheel screw M8x1, lenght aboaut 28mm. Suitable for Citroen 2CV starting from 1967. Reproduction
per piece. Note: Flywheel screws are necked-down bolts and should be always changed, if it released.
Fly wheel, bearing in the fly wheel. Mounting (guide) for the primary shaft. Suitable for Citroen
2CV. Inside diameter: 12mm, outside diameter: 18mm, height: 18mm.
Flywheel / crankshaft, bearing in the flywheel. Mounting (guide) for the primary shaft. Suitable
for Citroen 2CV4 + 2CV6, up to year of construction 02/1972. Design = needle bearing. Inner diameter: 12mm, outer diameter: 18mm, height: 10mm. Or. No. ZC9620 322U
Flywheel / crankshaft, bearing in the flywheel. Mounting (guide) for the primary shaft. Suitable
for Citroen 2CV6, from year of construction 03/1973 to 1990. design = needle bearing. Inner diameter: 12mm, outer diameter: 18mm, height: 16mm. Or. No. AM9121 100L
Flywheel, new part (heavy version). Suitable for Citroen 2CV6, from 1970 to 02/1982. Weight
approx. 12kg. Also suitable for Citroen Dyane, AK, AMI. All 602cc engines with front drum brake. Or. No. AY8312-000.
Fly wheel, new part. Suitable for Citroen 2CV 6, starting from year of construction 03/1982. We let
produce again the complete fly wheel with gear rim, since the old gear rims are often worn. The fly wheel is fine-heaved and ready for assembly. Or. No. 95559486. Produced in Europe.
Fly wheel, shaft seal for the gearbox main shaft (primary shaft) in the fly wheel. Suitable for
Citroen for 2CV6. Size: 11,9x18x4mm. Or. No. 95495074. Made in Germany.
Fly wheel, shaft seal for the gearbox main shaft (primary shaft) in the fly wheel. Suitable for
Citroen for 2CV6. Size: 12x18x3mm. Or. No. 7903078053. Made in Germany.
Centrifugal weights ignition timing, reproduction, original not available any more, per piece, bad
d reproduction. 2CV after 1967.
Centrifugal weight suitable for the ignition, for Citroen 2CV, of year of construction 1955 to
1967. Per piece. Or.Nr.: AZ211-6A
Distributor cam of the ignition, for Citroen 2CV6. Very bad reproduction. We recommend the
replacement on an electronic ignition.
42 Articles
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
