Brake line flaring tool, for brake and hydraulic lines. Particularly for Citroen connectors. With
thrust pieces for 3,5mm + 4,5mm lines (8,0mm + 9,0mm Clinch screws).
special tools for motor vehicles for Peugeot AK-AZU
120 Articles | Page 2 of 3
Hog Rings (500 per pack) for 21048 automatic pliers (coverings). Suitable for Citroen, Peugeot
Renault. The suitable pliers have our number 21048.
Clutch Alignment Tool, Universal. For single plate clutches. Suitable for flywheels with or without
pilot bearing. Fast to fit and remove. Universal applications. Size of collets: 14mm to 28mm across 3 adaptors. Cone size range from 35mm < 67mm (for almost all classical french cars)
VIDEO 
Ligarex, specially pliers for clip strap (bellow straps). This securement was used at many French
classic cars, for all kind of hose securement, like radiator hoses, collars, rubber bellows of the heating etc. With Ligarex you re-establish the original optics and you have always the suitable length in the workshop!
Magnetic lifter flexible + washing nozzles adjustment tool. This magnet lifter can be extended up
to 592mm and is flexible at the end. Also the nut in the intake tract far behind is brought out with it again! Additionally it has a steel needle in the handle, with which washing nozzles can be adjusted.
Magnetic bowl, stainless steel bowl with magnetic base and soft rubber shell. Very useful to
collect small parts! 150 mm diameter
Open end wrench 50mm, for the nut from the suspension pot - threadet pipe (3453-T). Simple quality
for hobby. Suitable for Citroen AK, ACDY, AMi6+8, AZAM6. Made in Germany.
Oil drain screw thread repair set for the following threads: M10x1.5, M12x1.5, M14x1.5, M16x1.5. 64
pieces. Scope of delivery: 4x tap drill, 5x plug screw for each thread size, 10x sealing ring for each thread size.
Oil absorbent pad. Extremely absorbent. Dimension: 51x38cm. For oils and brake fluids. Attention
the pads do not suck and absorb water! Your wife will be grateful!
Oil cooler tool (to loosen the union nut of the oil line that goes into the engine block). Suitable
for Citroen 2CV6 + 2CV4. Dyane, Mehari, AMI (it is possible to mount the oil cooler without dismantling the engine fan housing)
Hog Ring Pliers for use with A7 Hog Rings (Part No 21049). Complete with automatic feed. Ideal for
continuous connections. Single handed operation. Ideal for upholstery on classic cars.
Hog ring plier for the mounting of coverings (workshop quality). With this pliers the hog ring`s
18420 are optimally treated.
Wheel Stud Restorer Kit. For repairing damaged wheel stud threads using a reverse action to ensure
the alignment of the thread. Includes adaptor sizes: M12 x 1.25mm. M12 x 1.5mm. M14 x 1.5mm.
Rear wheel hub: Threating die for recutting the thread of the rear wheel hub - brake drum (where
the 44 nut is mounted). Suitable for all Citroen 2CV, Dyane, AK, AZU, ACDY, AMI 6+8, Mehari. Very good workshop quality!
Rear wheel hub: die holder (winch) for recutting the thread of the rear wheel hub - brake drum
Very good workshop quality!
Revolver hole punch. For diameters of: 2.0 + 2.5 + 3.0 + 4 + 4.5 mm. The lever ratio requires less
effort. These hole punches are actually known for belt holes. However, we use them to punch holes in the jute tensioning cover under the seat covers in the Citroën 2CV or Dyane. This makes it much easier to install the tensioning rubbers.
Rust eraser pen. Ideal for removing even the smallest rust spots. Indispensable! And, of course
the cleaned rust spot must then be preserved with paint immediately.
Discs (windscreen) Pull-in tool (cord with handle). This is used to pull the rubber lip of the seal
over the sheet metal fold. Very helpful!
Windscreens (windscreen) piping assembly tool - bracket inserts. For small piping. There are 5
brackets in different widths so that narrow and wide piping can be fitted (e.g. for the 2CV, R4....). Suitable for tool with item number 20134.
Windscreen Installation Tool Set. Windshield sealing trim assembly tool. With this tools will the
rubber lip (seal) inclination (spread) and it can fit the sealing trim at the same time. Attention: The tool is for very wide piping. For chrome piping e.g. Citroen 2CV, Renault R4 etc. small brackets must be fitted. See our item number 20137.
Trakrite Wheel Alignment Gauge. Trakrite is the simplest, most accurate device for checking the
alignment of the steered wheels of car and light commercials. It is a roller bearing platform over which one front wheel is slowly driven with the wheels in their straight ahead position.
Tie rods + tie rod end separator. Suitable for Citroen 2CV, DS, 11CV, 15CV. Renault R4, R5. Peugeot
404 etc. clamping range 16-18mm. Opening 19mm!
Tie rod end wrench (630-16/2), for the nut in the tie rod end. Suitable for Citroen 2CV. Note: this
tool do not fit for tie rod end with strengthened nuts.
Temperature indicator (laser), electronic, ideal for motor vehicle sector for instance to check on
elbow wether all cylinders are working optimal or to check water temperature, etc. Very easy to use, good quality professional product!
Separation Fork Set, 5 pcs., forged carbon Steel 3 forks opening: 17,4 mm - 23,8 mm - 28,5 mm. 1
1 handle 200 mm long. 1 adapter for impact hammer 10 mm shaft-ø, 175 mm long.
Transfer pump metal version, inclusive 2 hoses for drawing in and running off, 500ccm. Applicable
e for: Diesel, fuel oil, coolant, brake fluid.
120 Articles | Page 2 of 3
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
