Cover sheet (sliding sheet metal, in front + rear suitable) for the case of the steering gear
Suitable for Citroen 11CV sheet Or. Nr.601938 + 601939
steering gear for Alle Alle
139 Articles | Page 1 of 3
Spacer 0,3mm (3 item), for the lower steering gear case (between steering column bottom and
steering gear). Suitable for Citroen HY. Or. Nr. HY442-81B
Bolt in the steering gear. (2x bolts, 3x seat shell). Repair kit, ball diameter 25mm. The bolts
take up the tie rods. Suitable for Citroen 11CV + Citroen HY, from year of construction 1948 to 1965. Or. No. 601847, 601849, 601836
Dauphine, collar steering gear (per piece). Openings 31mm + 25mm. Minimum lengthens 95mm, maximum
length 230mm. Diameter over all 68mm.
Flexible disk for the steering column. Suitable for Renault R4, R5, R8, R16, R18, Dauphine. Outside
diameter: 76mm. Inside diameter: 24mm. Pitch center diameter: about 50mm.
Ball pin (2x) with bearing shells (4x), for the steering gear. Suitable for Citroen HY, starting
from year of construction 04/1969. Ball pin length: 84mm. Thread: M12 x 1,5. Or. No. HY442-100. Bearing shells diameters: 28mm. Amount: 11,7mm. Or. No. HY442-242A. Since the year of construction 05/1972, the bearing shells are Installed.
Bearing bush with rubber, for the steering column at the top. Suitable for Citroen 11CV + 15CV
Citroen HY, to year of construction 1965. Dimension: 36.7 x 22.5 x 30mm. Or. No. 604129 + 604130
Bearing for the steering column bottom (needle bearing bush). Suitable for Renault R5, Super5
Rapid, R9, R11, R18, R25, R30, Alpine, Espace 1, Fuego, Master 1. Inner diameter: 18,5mm. Outside diameter: 37,0mm. Overall height: 20mm. Or. No. 7703090293
Steering gear for Citroen DS, in the exchange. Suitable for hydraulic system LHM (power steering)
The steering unit is built up with newest seals and can be used for LHM liquid! Or. No. 9D5409726V. Plus 400 Euro Old part deposit. Note: The steering unit must be installed after the Citroen workshop specifications (workshop book 583, book 2, workingpaper D.444-1). You must have the tool 39002 (for the angle position of the steering gear to the steering column). Without this tool, you can not work!
Steering gear for Citroen DS, in the exchange. Suitable for hydraulic system LHS (power steering)
The steering unit is built up with newest seals and can be used for LHS liquid! Plus 400 Euro Old part deposit. Note: The steering unit must be installed after the Citroen workshop specifications (workshop book 583, book 2, workingpaper D.444-1). You must have the tool 39002 (for the angle position of the steering gear to the steering column). Without this tool, you can not work!
Steering gear repair set for the tie rod guide. Suitable for Citroen 2CV. Consisting of: Pin + seat
bowls + guides, ball pin, rubber,
Steering gear repair set. Suitable for hydraulic systems LHM. Suitable for Citroen DS, starting
from year of construction 07/1967
Steering gear: Pressure spring for the damping pushrod of the steering rack. Diameter: 16.5mm. Or
No. D442-2 + 5411166. Suitable for Citroen DS.
Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. Splines (worm gears) are continuous
up to the bearing. Suitable bush = 12233.
Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. First version. Splines (worm gears)
go only up to the half height of the bearing. Shaft diameter at the lower end = 13 mm.
Steering worm of 8 teeth, inclusive bearing, for Citroen 2CV. Good reproduction! The suitable guide
bush down (10mm inside diameter) has our No. 12232. Overall length: 112,8mm.
Steering worm of 8 teeth, inclusive bearing, for Citroen 2CV. Inside diameter: 10mm. Suitable lower
bush = 12232. Overall length: 112,8mm.
Steering worm bearing bush (down at the needle bearing). Suitable for Citroen 2CV. The bearing is a
needle bearing! Only for steering worm with 8 teeth. Inside diameter: 10mm. Outside diameter: 14mm. Overall height: 12mm.
Steering worm bearing bush (down at the needle bearing). Suitable for Citroen 2CV. The bearing is a
needle bearing! Only for steering worms with 8 teeth. Inside diameter: 12mm. Outside diameter: 18mm. Overall height: 12mm. Manufacturer SKF.
Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF
Inside diameter 10mm, outside diameter 17mm, height of 12mm
Steering worm bearing bush 2CV, down at the steering worm. (no needle bearing). Inside diameter
10mm, outside diameter 16mm, height of 10mm
Steering worm locking cap down (the cap is hit from downside into the steering gear). 20mm
Suitable for Citroen 2CV.
Steering worm nut with sealing ring. Suitable for Citroen 2CV, starting from year of construction
03/1971. From own production, with interchangeable shaft seal. Very significant.
Steering worm nut shaft seal (as substitute for 12140). Suitable for Citroen 2CV, starting from
year of construction 03/1971. Dimension: 19 x 27 x 5mm.
Steering, repair kit (assembled). Suitable for Citroen 2CV up to Orga No. 2275, Dyane, Mehari
Consisting of the complete guide in the front axle tube, incl. new rack, 24 teeth. Good quality. This is the old version of the steering rack for a steering pinion with 7 teeth!!! Made in Europe
Steering unit, repair set. Suitable for Citroen 2CV. Consisting of: Guide steering unit pin, 2x
slide ring, ring for the gear rack ((27,75mm + - 1/10mm), rubber under the tie rods. Reproduction. Only for LHD, cannot use for RHD.
Steering unit - adjusting tool, suitable for Citroen DS. (1955-T). This tool is for the adjustment
of the steering column to the steering gear. It is indispensable, for the installation of a new steering unit!
139 Articles | Page 1 of 3
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
