P 204/304/404/504, flexible disk steering column. Suitable for Peugeot 204, 304, 404, 504. Pitch
h diameter: about 50mm. Or. No. 4040.14
for Peugeot 404
1475 Articles | Page 15 of 30
P 204/304/404/504, rear axle rubber stop. Diameter: 55mm. Height: 53mm. Suitable for Peugeot 204
304, 404, 504. Or. No. 3514.12
P 204/304/404/504, gear knob for steering wheel gear change. Please note: this is the rubberised
version (not Bakalit). Suitable for all Peugeot 204, 304, 404, 504 with steering wheel gear change! Or. No. 2401.16
P 204/304/404/Simca, wheel brake cylinder at the rear left. Suitable for Peugeot 204, 304, 404
Simca 1300, 1301. Piston diameter: 17,46mmmm (11/16 customs). Brake pipe connection: 3/8 x 24UNF. Or. No. 4402.19. Made in France
P 204/304/404/Simca, wheel brake cylinder at the rear right. Suitable for Peugeot 204, 304, 404
Simca 1300, 1301. Piston diameter: 17,46mmmm (11/16 customs). Brake pipe connection: 3/8 x 24UNF. Or. No. 4402.20. Made in France
P 204/304/504/505/604, shaft seal wheel bearing (exterior). Outside diameter: 70mm. Inside
diameter: 55mm. Height: 10mm. Suitable for Peugeot 204, 304, 504, 505, 604. Or. No. 3346.06
P 204/304/Talbot, brake pads in front, brake system Lucas/Girling. Suitable for Peugeot 204 + 304
starting from year of construction 08/1966. Talbot 1200/2 series. Without connections for brake wear control. Wide one: 63,4mm. Height: 55,0mm. Heavy one: 14,5mm.
P 204/403/404/504, wheel bearing rear (exterior bearing). Outside diameter: 52mm. Inside diameter
20mm. Wide one: 15mm. Suitable for Peugeot 204, 403, 404 + 504. Or. No. 3735.03 Made in Spain
brake blocks front Peugeot 204, 404, system Girling, 4245.35, 204 08/65>08/66 (1 set = 4 pieces)
404 67>09/68 Thick 15,5mm, W x L = 81x66mm
P 204/404/202, brake hose front, suitable for Peugeot 204 + 404, up to presumably year of
construction 1966. Peugeot 202 rear. Length: 376mm. Thread inside: 3/8 x 24 UNF (both sides). Thread outside: 5/8 x 18 UNF (both sides). Attention: These brake hoses are for brake line flare bolts with thread offset at the bottom! From approx. year of manufacture 1966 the flare screws have been replaced by a full thread! Made in Europe.
brake hose Peugeot 504 front 09/75-10/82, P 304, P305,P404,P604, length 401mm, connections male
thread M10 + female thread 1x M10. Made in Europe.
brake hose Peugeot 404, P305 front left 72-80, length 351mm, connection 1x M10 outside + 1x M10
inside. Made in Europe.
P 403/404, release bearing fixing clip (short version). Suitable for all Peugeot 403 + Peugeot 404
(C3 gearbox). Attention: Long (71425) and short clamps (No. 71426) have been fitted. Depending on the version. Or. No. 2049.03
P 403/404, release bearing fixing clip (long version). Suitable for all Peugeot 403 + Peugeot 404
(C3 gearbox). Attention: Long (this) and short clamps (No. 71426) have been fitted. Depending on the version. Or. No. 2049.05
P 403/404, clutch release sleeve, for C3 gearbox (not suitable for BA7). Suitable for Peugeot 403 +
404, to year of construction 1967 (excluded 403 U8, 403/7 Diesel). For all engines. The clutch release sleeve is running in ball bearings. Or. No. 2041.11. Please preload the clutch adjust again. Peugeot work instruction 2/0101 0102 + 2/0201 + 2/0401 > 0405.
PDF FILE 
P 403/404, brake shoe spring set (front axle). Suitable for Peugeot 403 + Peugeot 404 (vehicles
without brake booster). Or. no. 4308.04.
P 403/404, front brake shoes. Suitable for Peugeot 403, all years of construction. Peugeot 404 from
year of construction 1961 onwards. Brake drum diameter: 255 mm. Brake lining width: 50 mm.
P 403/404, brake hose rear. Length: 495mm. Suitable for Peugeot 404, first years of construction
Peugeot 403. Simca Aronde. Thread: 1 side male thread 5/8-18H + female thread 7/16-20H. Other side: Male thread 7/16-20H. Made in Spain.
P 403/404, brake hose in front Peugeot 403 first model, Peugeot 404 first model, Simca Aronde
Overall length 410mm. Male thread 7/16 x 20 UNF, other side 7/16 x 20 UNF female threads, about 16mm male thread. Or. N0. 4806.05. Made in Spain.
P 403/404, seal Dieselfilter Bosch. Dimension: 75x83x3mm. Suitable for Peugeot 403 Diesel + 404
Diesel. Or. No. 1912.01
P 403/404, seal for the lid of the fuel sender (Jaeger). Suitable for Peugeot 403 + 404. Or. No
1526.06. Original Peugeot, no reproduction!
P 403/404, master brake cylinder. Piston diameter: 22mm. Brake line connector: 1/2 x 20 UNF. Brake
fluid reservoir thread: about: M19 x 1,5. Suitable for Peugeot 403, starting from year of construction 10/1960. Peugeot 404, starting from year of construction 07/1960. Not suitable for Thermostable brakes. Or. No. 460112. Made in Europe.
P 403/404, master brake cylinder. Suitable for Peugeot 403 + 404. Piston diameter: 17,46mm (11/16)
Thread brake fluid reservoir: 19mm.
P 403/404, crankshaft bearing, 0.8 oversize. Suitable for Peugeot 404, of year of construction 1961
to 1964 (starting from engine 4036261, 3 crankshaft bearings, 1618cc). Peugeot of 403, final years of construction.
P 403/404, air cleaner element round, for Peugeot 403 + 404. Height of 125mm, outside diameter
110mm, inside diameter 67mm.
P 403/404, clutch disk for Peugeot 403 Diesel + 404 Diesel to year of construction 1967. For
engine: XDP85. Dimension: 200 x 30 x 10mm. Note: adjust the clutch free travel! Peugeot work instruction 2/0101 0102 + 2/0201 + 2/0401 > 0405.
P 403/404, clutch disk. Suitable for Peugeot 403, of year of construction 1956 to 1964. Peugeot
404, of year of construction 1960 to 1967. Diameter: 215mm, 30x25x10. Teeth: 10. Lining thickness: 7,9mm. Or. No. 2054,16 + 2054.21. Note: adjust the clutch free travel! Peugeot work instruction 2/0101 0102 + 2/0201 + 2/0401 > 0405.
Wheel brake cylinder rear left, for Peugeot 403 and 404, piston:15/16 inch,(23,81mm). Connector 3/8
x 24UNF. Or.Nr. 440226. Made in Europe.
Wheel brake cylinder rear right. for Peugeot 403 and 404, piston:15/16 inch,(23,81mm). Connector
3/8 x 24UNF. Or.Nr. 440227. Made in Europe.
P 403/404, wheel brake cylinder with 1 piston 30mm,brake line connector 3/8 x 24UNF (9,5mm),403 Bj
1961->, 404, 404 Comercial, 404 Pick UP. Mounting board bore 21,5mm, , length over all 63,5mm. Made in Europe.
wheel brake cylinder repair set front 403+404 with 1,1/8 inch piston till model changing 1965
Themostable brakes came
P 403/404, wheel brake cylinder in front. 1 piston (30mm). Brake line connector: 7/16 x 20 UNF (E
Flanging). Suitable for Peugeot 403 + 404 (starting from year of construction 1965). Mounting board bore 22mm. Length over all 65mm. Or. No. 4401-20. Made in France
P 403/404, wheel brake cylinder in front. Fits on the left + on the right. Suitable for Peugeot 403
(7-D-BD-U-L). Peugeot 404B + Coupe. Piston diameter: 28.57 mm. Brake line connector: 7/16 x 20UNF. Mounting board bore: 22mm. Or. No. 4401.14. Installed on vehicles, before year of construction 10/1964! Made in France
P 403/404, carburetor Solex 34BICSA (no reproduction). Carburetor diameter: 34mm. Suitable for
Peugeot 403, 404, J7, J9. Original SOLEX carburetor, no reproduction. Or. No. Solex: 13550 000. Or. No. Peugeot: 1401.93
P 403/404, carburetor Solex 34BICSA12 (no reproduction). Carburetor diameter: 34mm. Suitable for
Peugeot 403, 404, J7, J9. Original SOLEX carburetor, no reproduction. Or. No. Solex: 13549 000. Or. No. Peugeot: 1401.66
Starter lock (in the dashboard), suitable for Peugeot 403 + 404 (first version). 3x connection
Case diameter: 39mm. Lockbolt: 8x13 mm. Case high over everything: 64 mm (without cable connections)
Guide sleeve for the horn actuation rod in the steering column. Suitable for Peugeot 403, 404
partly 504. Material Celaron. 2,7x6x15mm. Or. No. 626305
1475 Articles | Page 15 of 30
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
