used for dashboard, door linings. Suitable for Citroen 2CV, DS, HY and in many Peugeot + Renault. Our rosettes are shiny and flanged at the back. This makes them very stable.
used for dashboard, door linings. Suitable for Citroen 2CV, DS, HY and in many Peugeot + Renault. Our rosettes are shiny and flanged at the back. This makes them very stable.
e used for dashboard, door linings. Suitable for Citroen 2CV, DS, HY and in many Peugeot + Renault. Our rosettes are shiny and flanged at the back. This makes them very stable.
the cleaned rust spot must then be preserved with paint immediately.
improvement for classic vehicles that use a hand pump without a ball valve to deliver water. This ensures that windscreen washer fluid is always available at the spray nozzles. Please note the direction of flow during installation! It also prevents petrol from flowing back in the fuel line (useful for longer periods of inactivity). Please install this valve close to the petrol pump (between the petrol pump and the tank).
E") 1 thread light, only brake or taillight! With metal base + support! The glass has 68,5mm diameter! Used in HY, AZU, DS - in many Renault + Peugeot models as well!
were used in many French cars!
classic cars. Diameter: 56mm.
button and not a toggle switch. The push button is useful for electric windscreen washers, horns or headlight flashers, for example. Dimensions: 36x18mm (French standard size). Suitable for Peugeot, Citroen, Renault.
switch for e.g. heater blowers, additional consumers.... Dimensions: 36x18mm (French standard size). Suitable for Peugeot, Citroen, Renault.
Peugeot 504. Or. No. 2454.55
over the sheet metal fold. Very helpful!
brackets in different widths so that narrow and wide piping can be fitted (e.g. for the 2CV, R4....). Suitable for tool with item number 20134.
rubber lip (seal) inclination (spread) and it can fit the sealing trim at the same time. Attention: The tool is for very wide piping. For chrome piping e.g. Citroen 2CV, Renault R4 etc. small brackets must be fitted. See our item number 20137.
rubber-mounted front, rear and side windows. Very stable, water resistant, remains elastic. Good adhesion even on damp windscreens.
to sealing rubber-mounted front. - Tail and side windows. Very stably, water-resistant, remains elastic. Good adhesion also on wet disk.
reservoir is supplied with mounting and accessories and can be installed in any vehicle, e.g. Citroen Mehari, Renault R4 first versions, etc. This type of windscreen washer reservoir has also been installed in many Italian vehicles (Alfa Romeo Spider...).
h push-button, cable, cross bars etc. very practical and small. Width 19,5cm, height of 16,5cm, depth 5,5cm
overall height totally: 185mm. Building depth altogether: 100mm. The reservoir is supplied with fixture. The fixture is from the rear at the reservoir.
with a nut from rear. 1 water jet. Low body height. Mounting diameter: 8,0mm.
screwed with a nut from behind. 2x water jet. Flat design.. Mounting diameter: 8,0mm.
connection from above! Made in the European Union. The picture indicates the correct mounting position. The pump section is down, the electric motor above!
mounting! Suitable for Citroen 2CV. In addition, the pump can be universal installed.
for many French vehicles.
diameter of 190mm, but is suitable for a lens with 180mm diameter. Quality reproduction. The original headlight can be repaired with this. Simply remove the glass cleanly (the old reflector may be damaged for this) and glue it onto the new reflector. Suitable for Renault: Floride, Caravelle, Fregate, R8 Gordine. Peugeot 203, 403, 505, Citroen DS up to 1967.
handbrake cables, speedometer cables, petrol hose... External dimensions: 23x30mm. Inner diameter: 8mm. The rubber is slit on one long side, and can therefore be easily placed over the cable to be protected!
External dimension: 42mm. Length: 31mm. Inner diameter: 12mm. The rubber is not slit (but of course this can be done afterwards if it makes assembly easier)
can easily produce bent water hoses. Simple and ingenious!
can easily produce bent water hoses. Simple and ingenious!
can easily produce bent water hoses. Simple and ingenious!
can easily produce bent water hoses. Simple and ingenious!
can easily produce bent water hoses. Simple and ingenious!
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
