for Peugeot Sonstige-Peugeot

P 305, gas-filled spring rear flap Peugeot 305. Or.Nr.873149.

P 305, hand brake cable Peugeot 305 I. all models. Fits on the left + on the right. 1588mm

lengthens. Sleeve 890mm. Or. No. 4834.71

P 305, heater radiator. Suitable for Peugeot 305. Or. No. 6448.39.

P 305, radiator hose above Peugeot 305. Suitable for all petrols. Or. No. 1343.46

• Suitable for this article
• 
  Hose clamp 32-44mm, especially for radiator hose. Vintage look. Embossed band
  4,56 €
• 
  Hose clamp 38-50mm, especially for radiator hose. Vintage look. Embossed band
  4,71 €

P 305, clutch cable. Suitable for Peugeot 305, starting from year of construction 1982. Or. No

2150.61

P305, steering box switch for wiper. 2 Version. Or.No.623904

brake hose Peugeot 404, P305 front left 72-80, length 351mm, connection 1x M10 outside + 1x M10

inside. Made in Europe.

P 402, cylinder head gasket for Peugeot 402 /12CV. Original Exelsior. New Old stock.

P 403/404/504/505, bearing for the jackshaft, rear (gearbox BA7). Suitable for Peugeot 403, Peugeot

404, Peugeot 504, Peugeot 505. Outside diameter: 47mm. Inside diameter: 21,5mm. Overall height: 16.25 mm. Or. No. 2372.11

P 403/404/DS, headlight insert (NOS). Ducellier design. Suitable for Peugeot 403 + 404. Citroen DS

up to year of construction 1967. 180 mm diameter. Holder for a double filament bulb. Please note: These are original headlights from the manufacturer CIELCO in Spain. Found in a warehouse clearance (new old stock). The headlights have a test mark!

• Suitable for this article
• 
  Double filament bulb 45/40W, 12V.
  2,93 €
• 
  H4 bulb with two-filament base, 12V,
  7,83 €
• 
  Two-filament bulb 40/45 W, 12 Volt, yellow ! Not allowed in German traffic
  9,38 €

P 403/404/J7, rear brake hose. Suitable for Peugeot 404 up to the year of construction 1966

Peugeot 403 second model. J7 first model. 5/8 UNF male thread. 7/16 UNF female thread. Length 485mm.

brake hose Peugeot 404. rear 72-80, length 205mm, C15, Peugeot 305. connection male thread 2x M10

10

P 404, clutch release yoke, for hydraulic clutch. Suitable for Peugeot 404 Diesel, starting from

year of construction 1967. Peugeot 305, 309, 405. Citroen C15, Citroen BX 19, starting from 1987. Or. No. 2117.42

• Suitable for this article
• 
  Bush for the clutch fork. Suitable for some Peugeot 205. Citroen C15, BX. Or
  2,13 €

P 404/403/504/J7, sealing ring for the liner, bottom (sealing in the engine block). Dimensions

78.2 x 81.8 x 5.0mm. Suitable for Peugeot 403 (engine 8CV TN3). 404 (Engine 8CV + 9CV > 1970). 504 (XM1L8). J7 until 1970. Or. No. 0112.17. Made in Germany

P 404/504, clutch release yoke for BA7 gearbox (Bowden cable). Suitable for Peugeot 404, starting

from year of construction 1967. Peugeot 504 + 505. Length: about 195mm. Or. No. 2117.41

P 404/504, crankshaft bearing, oversize 0,30. Suitable for Peugeot 404, from year of construction

1970. Peugeot 504 (03/1971 - 10/1971). Peugeot 505 (09/1980 - 10/1981). J5 (03/1980 - 10/1981). J7 (09/1968 - 03/1980). For engines: XC5P, XC6, XC7, XC7P, XM7P, XN1, XN1P. 1618cc, 1796cc, 1971cc.

P 404/504, crankshaft bearing, oversize 0,50. Suitable for Peugeot 404, from year of construction

1970. Peugeot 504 (03/1971 - 10/1971). Peugeot 505 (09/1980 - 10/1981). J5 (03/1980 - 10/1981). J7 (09/1968 - 03/1980). For engines: XC5P, XC6, XC7, XC7P, XM7P, XN1, XN1P. 1618cc, 1796cc, 1971cc. Diameter 58,9/58,0/56,7/56,65/54,4 width 29,5/21,5/29,3

P 404/504, circlip for clutch slave cylinder (72351 + 72224). For 36mm groove diameter. Suitable

for Peugeot 404 + 504, 505, J7.

P 404/504, shock absorber rear (1 piece). Suitable for Peugeot 404 + 504. Partial Peugeot 505. The

shock absorber has down a bonded-rubber bushing, above threaded pin!

P 404/504/505, Allen screw for the clutch securement. Suitable for Peugeot 404, 504 + 505. Thread

M12x1,5. Length: 64mm. Or. No. 6913.61

P 404/504/505, universal joint at the gearbox outlet, for the cardan shaft. Suitable for Peugeot

404, of year of construction 11/1967 to 12/1971. Peugeot 504 (1796cm ³, 1971cm ³, 2664cm ³) sedan, BREAK, Cabriolet + Coupe. Peugeot 505 (all engines). Number of teeth: both sides 25. Or. No. 2619.17

P 404/504/505, clutch release yoke, for hydraulic clutch (gearbox BA7). Suitable for Peugeot 404

starting from year of construction 1967. Peugeot 504, Peugeot 505. Or. No. 2117.39

P 404/504/505, bearing for the gearbox main shaft. Suitable for Peugeot 404, Peugeot 504, Peugeot

505. Outside diameter: 75mm. Inside diameter: 35mm. Overall height: 20mm. Or. No. 230810

P 404/504/505, liner gasket bottom. Fits Peugeot 404 from year of construction 01/1970 (engine XC7

CM7). 504/505 from 01/1971 (engine XM7, XN1, XN1A). J7 (engine XM7P + XC7P). Engines until year of construction 06/1984

P 404/504/505, clutch disk. Dimension: 215mm x 29 x 10mm. 6 springs, 10 teeth. Suitable for Peugeot

404, starting from year of construction 1967 (all petrols). Peugeot 504 + 505 petrols, with 215mm pressure plate and 6 springs in the clutch disk.

P 404/504/505, engine suspension in front. Suitable for Peugeot of 404 Diesel, 504 Diesel, 505

Diesel. Hole spacing: 85mm. Or. No. 1807.28

P 404/504/505, engine suspension in front. Suitable for Peugeot 404, Peugeot 504 + 505. The engine

suspension fits on the left of or on the right. Engine: XN6. Hole spacing: 86 mm. Or. No. 1807.25

P 404/504/505, belt pulley on the crankshaft. Suitable for Peugeot 404, 504, 505. Or. No. 0515,46 +

0515E2. Diameter: 13,10cm. Outside diameter of the scroll seal: 45,35mm.

P 404/504/505, bonded-rubber bushing, for the fixture plate spring rear axle. Suitable for Peugeot

404, 504, 505. Inside diameter: 16mm. Outside diameter: 32mm. Length inside: 69mm. Length outside: 60mm. Or. No. 5131.39

P 404/504/505, shaft seal (with metal inset) for the wheel hub rear (full-floating axle)

Dimension: 53 x 79 x 10mm. Suitable for Peugeot 404, 504, 505. Or. No. 3345.31

Valve timing cover seal. Suitable for Peugeot 404 with carburetor engine. Peugeot 504 (carburetor)

505 (carburetor). Or. No. 0321.11. Made in Germany.

P 404/504/505, cylinder head screws (10 item). Suitable for Peugeot 404, 504, 505, J5 Citroen C25

All fuel engines (XM7 + XN1) from 1,6L to 2.0 liters engine capacity. Thread: M12. Length: 144mm. Or. No. 0204.21.

P 404/504/505/C25, valve cover gasket for Peugeot 404, all petrol engines. Peugeot 504 + 505 for

petrol engines to 1971cc. Citroen C25 petrol. Or. No. 0249.14

P 404/504/505/J5, engine gasket set. Suitable for Peugeot 404, 504, 505, J5, J7, J9. Petrol engines

1.6 + 1,8L (XM7, XM7A, XC7, XC7P, XM, XM7P). 86 mm bore. Inclusive Cylinder head gasket. Original supplier! Delivery without liners sealing rings!

• Suitable for this article
• 
  P 404/403/504/J7, sealing ring for the liner, bottom (sealing in the engine
  7,28 €

P 404/504/604/J7, clutch master cylinder sealing set. For piston diameters: 19mm. Suitable for

Peugeot 204, 304, 404, 504, 505, 604, J7.

P 404/504/694/J7/HY, cylinder head gasket Diesel, for engines XD4.88, XDP4.88, XDP4.90, XDP88

XDP90, XDPX90. (1948cc + 2112cc). Suitable for Peugeot 404 D, 504 D, 604 D, J7 Diesel. Citroen HY Diesel. Or. No. 0203.70

P 404/504/C25/J5, cylinder head gasket. Suitable for Peugeot 404, 504, 505, J5, J7, J9. Citroen

C25. Suitable for petrol engines 1,6L + 1,8L. Installed starting from 09/1970 ((XM7, XM7A, XC7, XC7P, XM, XM7P). 1,73mm heavily. 4 grooves.

P 404/504/J5, connecting rod bearing screw. Suitable for Peugeot 404 Diesel, 504D, 505D, J7D, J9D

Suitable for engines 2,1L, 2,3L, 2,5L. Diameter: 10,25mm. Length: 58mm. Per piece. Or. No. 0607.16

P 504 V6, piston ring set (for 1 piston), for 6 liners. Engine: ZNJK. Engine capacity: 2849cc

Bore: 91mm. Piston rings: 1,5mm + 2,0mm + 4,0mm. Suitable for Peugeot 505 V6, 604 V6. Renault 30, Alpine V6.

• Suitable for this article
• 
  piston ring presenting pliers for diameter 40-100.
  22,71 €
• 
  Piston ring compressor, 60 to 90mm clamping range. Hobby version (not for daily
  16,76 €

P 504 V6/R30, valve cover gasket on the left (made of paper, approx. 1 mm thick), for Peugeot

Renault V6, with valve cap from aluminum casting. (ZMJ). Suitable for Peugeot 504 V6, 505 V6, 604 V6, Renault R25 V6, R30, Talbot Tagora. Or. No. 0249.37

P 504 V6/R30, valve cover gasket on the right (made of paper, approx. 1 mm thick), for Peugeot

Renault V6, with valve cap from aluminum casting. (ZMJ). Suitable for Peugeot 504 V6, 505 V6, 604 V6, Renault R25 V6, R30, Talbot Tagora. Or. No. 0249.31

P 504, Bleeder screw rear brake caliper. Brake system: Lucas. Thread: 3/8 x 24 UNF. Length: 36,6mm

Suitable for Peugeot 504 and many other Peugeots.

wheel brake cylinder rear, left + right side, Peugeot 504 Pick Up >10/81, system Girling, 22.2mm

per piece

• Suitable for this article
• 
  Brake cylinder paste. Manufacturer: FÖRCH. 5g brake cylinder paste for
  5,31 €

P 504, tie rod completely (inclusive tie rod end + collar steering gear). Suitable for Peugeot 504

Cabriolet + Coupe. Also suitable for Peugeot 104, Peugeot 505. Citroen VISA. Or. No. 3812.15. The tie rod is on the left + on the right identically.

bleeder screw, brake, Peugeot 504, 505 front, >71 / length overall 30mm, M7x1. For brake system

LUCAS + ATE

• Suitable for this article
• 
  Dust cap from rubber, for the vent screw at brake calipers and wheel brake
  0,43 €

P 504/505, exhaust pipe center (for car`s with 2 silencers). Suitable for Peugeot 504 (petrol 2.0)

of year of construction 07/1972 to 12/1980. Engine: XN1 + XN2. Peugeot 504 Diesel (2,3D). Engine: XD2. Peugeot 505 (2.0, TI, STI). Or. No. 1722.15

P 504/505, brake shoes rear, system Lucas. 254x60mm. Or.Nr. 424152 + 424101.

P 504/505, front brake pads, TEVES (ATE) system, with wear indicator. Width 89,5 / height 70,0

thickness 19mm. Suitable for Peugeot 504 + 505.

Drum for Peugeot 504, 505. 254mm diameters. Height totally 70,5mm, interior height 55,5mm, interior

hole (mounting) 93mm. 4 hole rim. Or. No. 4247.17

P 504/505, spring plate above, starting from chassis 3972016. Suitable for Peugeot 504 + 505

Petrol + Diesel