Brake hose seal DOT (red). For DOT brake system (normal brake fluid DOT4). 4,5mm line (connector
M9). Suitable for Citroen 2CV + Citroen HY.
for Citroën 2CV AMI6-8
1728 Articles | Page 9 of 35
Brake light switch old version. Suitable for Citroen 2CV (6 volt), AMI6 + Citroen ID19, up to year
of construction 08/1961 (DM576-02, does not fit Citroen DS). The brake light switch is mounted in the engine compartment on the firewall. Reproduction. Or. No. AZ57602 (2CV). However, with a little skill, the brake light switch can also be converted to fit the DS19 with Or. No. DS576-02A. The brake light switch for DS19 is no longer available.
Stop light switch at the brake pedal. Connection flat plug. Connector: M12x1. Suitable for Citroen
2CV6, DS, CX, BX, HY, GS
Brake caliper mounting bolt washer (for bolt 13099). Suitable for Citroen 2CV6, Dyane, AMI8
Mehari. Please note: This washer is specially designed for the brake calliper. It is 3mm thick and black galvanised. If a normal washer (thinner) is used, the fixing screw is often too long! (Brake calliper cannot be fastened properly or gearbox housing tears)
Brake caliper sealing set. Suitable for Citroen 2CV, LHM system. Consisting of: 2 x seal + 2x dust
bag for the pistons, seal between the brake caliper halves, connecting tube brake caliper halves. Now improved version from Denmark!
Brake caliper seal (for sealing the two brake caliper halves) for our brake caliper 13013
Dimensions: 10 x 6.2 x 1.9 mm, suitable for Citroën 2CV, Dyane, AMI. Please note: Only suitable for our reproduction brake calipers 13013.
Brake caliper seal (for sealing the two brake caliper halves). Dimensions: 11 x 7.0 x 2.0mm
suitable for Citroën 2CV, Dyane, AMI. Please note: Only suitable for original brake calipers. Not suitable for reproduction brake calipers.
Front brake calliper, complete. New part! Suitable for Citroen 2CV, from year of construction 1981
to year of construction 1990 (8mm brake line screw connection). No old part return required! Attention: A 3mm washer must be used for the mounting screws (our number 1300) or continue to use the original washers. Without these 3mm washers, the fastening screws are too long!
Brake caliper halves connecting tube. Suitable for Citroen 2CV, starting from year of construction
1981. Caution, it gives also brake calipers, which were sealed between the halves only with an O-ring!
Brake disks "sport" front (2 pieces). Suitable for Citroen 2CV, from year of construction 1981 up
to 1990. The brake disks are perforated and have more brake power. The disks are particularly for operating tow trailer, 2CV van (if heavily loaded) etc. In normal driving mode, a conversion is not necessary.
Brake disks in front (2 fittings). Suitable for Citroen 2CV. Installed from year of construction
1981 to 1990. Reproduction.
Brake disks in front (2 pieces). Suitable for Citroen 2CV. Installed from year of construction 1981
to 1990. Original manufacturer quality. Of it their safety is dependant. Be careful: If the brake discs are installed at the front of your car: Just use hydraulic fluid LHM as brake fluid and never DOT4! DOT4 can destroy within 24hours the hole brake system. That is expensive und very dangerous. Every LHM brake part is green marked.
Brake hose mounting plate, rear left. Fits Citroen 2CV, up to year of manufacture 07/1964. The
brake hose is attached to the bracket with the banjo bolt (hence the 10mm hole in the bracket). Reproduction. Or. No.: A453-67
Brake hose mounting plate, rear left. Suitable for Citroen 2CV, from year of manufacture 07/1964 to
01/1972. The brake hose with its M14 thread is pushed through the holder and locked with a thin M14 nut (hence the 16mm hole)! Made of stainless steel! Or. No. AM453-67. Made in Germany.
Brake hose mounting plate, rear right. Suitable for Citroen 2CV, from year of manufacture 07/1964
to 01/1972. The brake hose with its M14 thread is pushed through the holder and locked with a thin M14 nut (hence the 16mm hole)! Made of stainless steel! Or. No. AM453-67A. Made in Germany.
Brake hose mounting plate, rear right. Fits Citroen 2CV, up to year of manufacture 07/1964. The
brake hose is attached to the bracket with the banjo bolt (hence the 10mm hole in the bracket). Reproduction. Or. No.: A453-67A
Brake hose rear, suitable for Citroen 2CV + AMI6, to year of construction 1966. Length: 310mm. One
side male thread M10x1. The other side has a female thread M10x1.
PDF FILE 
Brake hose rear, suitable for Citroen 2CV, starting from year of construction 1966. Length: 304mm
Both sides male thread M14x1,5 with additional female thread M9x1,25. Or. No. AM453-35
Brake hose in front, suitable for Citroen 2CV, starting from year of construction 1966. Length
280mm. One side male thread M12x1. One side female thread M10x1. Or.Nr.: AM453-29A. Made in Spain.
Brake hose in front, suitable for Citroen 2CV, to year of construction 07/1964. Length: 285mm. One
side male thread M12x1. The other side has female thread M10x1. Or.Nr.: AM453-29 AV. Made in Spain.
Brake hose in front, suitable for Citroen AK, AKS, AZU (van). Length: 302mm. 1 x male thread M12x1
1x male thread M14 x 1.5 with additional female thread M9x1,25.
Brake hose in front, suitable for Citroen AMI6. Length: 335mm. One side male thread M14x1,5 with
female thread M9x1,25. The other side has a male thread M12x1. Made in Spain.
Brake hose in front, suitable for Citroen Dyane 6, Mehari. Length: 222mm. One side male thread
M12x1. The other side has a male thread M14x1,5 with additional female threads M9x1,25. Made in Spain.
Brake drum rear (new part), with mounted wheel bearing. The brake drum is ready for assembly
mounted. Consisting of: New brake drum, new wheel bearing, new shaft seal, new wheel bearing screw. Suitable for Citroen 2CV.
Rear brake drum, new part. 180mm diameter, for the large wheel bearing. Suitable for Citroen AZU
AK, ACDY, AMI. The brake drum is supplied without wheel bearing.
Drum in front. Suitable for Citroen AK400, 350, AMI6, Dyane. 4 hole securement. 220mm diameter. The
drum is outside ripping. Or.No.: AM4516
Brake cylinder paste. Manufacturer: FÖRCH. 5g brake cylinder paste for hydraulic brake systems
For lubricating cylinder liners and pistons. Extends the service life of brake cylinders. Protects against corrosion. Compatible with DOT 3, DOT 4 and DOT 5.1 brake fluids. Keeps sleeves soft. Supports the installation of O-rings, lip seals, sleeves and other sealing elements made of rubber-elastic materials. Apply brake cylinder paste thinly and evenly on the surfaces to be lubricated. Attention: If you are installing a new wheel brake cylinder in your classic car, please coat the pistons and sleeves with this paste before installation. This will increase the longevity of the new brake parts on cars that are driven occasionally.
Choke cable old version, without light. Suitable for Citroen 2CV, Dyane, AMI6+8 until 1976, length
to 1500mm (can be shortened)
Choke cable with oval knob. Suitable for Citroen 11CV/15CV, starting from year of construction
07/1952. Length: 810mm. This choke cable can be installed also universal. Or. No. 723171
Choke cable, final version for Citroen 2CV + Dyane. For the square mounting. The choke cable is
illuminated! Or. No. 95597858
VIDEO Autosol chrome polish. 75 ml tube. (Premium chrome shine care). Autosol chrome polish has been
around for ages and has often been copied! Made in Germany.
Citroen emblem (Chevron) on the dashboard. Suitable for Citroen 11CV + 15CV, up to year of
construction 02/1952. Or. No. 802594. Dimension: 38 x 40mm. The emblem can also be used universal.
1728 Articles | Page 9 of 35
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
