Red indicator light, large, cone-shaped (LED), 6 Volt. Reproduction of the original lights. So
visually "nostalgic" but with modern technology! Suitable for Citroen 2CV (old models), AZU, HY, DS. Diameter for installation: 17.0 mm
for Citroën 2CV AMI6-8
1728 Articles | Page 18 of 35
Control light red, largely, conically. Reproduction of the original lights. Unfortunately the
quality is not so good. Suitable for Citroen 2CV, DS, HY.
Universal joint suitable for the drive shaft, for Citroen 2CV from the sixties + fifties
Reproduction. 25mm diameter, 57mm long. Significant reproduction. Or.Nr.: A37203
Universal joint suitable for the drive shaft, for Citroen 2CV from the sixties + fifties
Reproduction. 25mm diameter, 61mm long. Or.Nr.: A37203
Universal joint retaining ring (check ring) for the drive shaft. Suitable for Citroen 2CV from the
fifties to seventies. AM372-6C
Elbow seal exhaust 2CV6, improved version. The seal is made of most significant seal material
Preparation of Reinz Germany.
Exhaust manifold gasket made of copper 2CV6 (pure copper, 1.5mm thick!). Suitable for all 597/602cc
engines. Citroen 2CV6, Dyane 6, ACDY, Mehari, AMI8. Made in Germany
Elbow seal inlet 2CV6, improved version. The seal is made of most significant seal material
Preparation of Reinz Germany. Measurement: 28,3x43,75. Or.Nr.: 96177787
Manifold seal inlet, for 602cc engine. Citroen 2CV6. Or.Nr. 96177787. Measurement: 28,3x43,75mm
Original equipment manufacturer "Glaser"
Manifold seal inlet, for Citroen 2CV AZAM. Inside diameter: 34mm. Diameter securement: 8,0mm
Center to center securement: 55mm. Or.Nr.: AM1412C
Ball valve for Solex carburetor 30/32/34 PICS. Suitable for Citroen 2CV4 + 2CV6 with single
carburetor (round carburetor). Also suitable for Peugeot + Renault.
Clutch set for Citroen 2CV6 + 2CV4, of year of construction 1970 to 1982. (For vehicles with drum
brake in front). Dyane of year of construction 1968 to 1982. Mehari from 1968 to 1982. The clutch set consists of: Pressure plate (3 levers) clutch disk and clutch release sleeve. Reproduction, made in Europe. Note: The clutch must be adjusted after Citroen work instruction A.312-00! Made in Europe
PDF FILE 
Clutch completely, for Citroen 2CV6, of year of construction 03/1982 to 1990 (disc brake in front)
Dyane 6, starting from year of construction 1982. Mehari, of year of construction 4/1982 to 1990. Manufacturer: Valeo. 18 teeth, diameters: 160mm. (Multi-disk) new part.
Clutch Alignment Tool, Universal. For single plate clutches. Suitable for flywheels with or without
pilot bearing. Fast to fit and remove. Universal applications. Size of collets: 14mm to 28mm across 3 adaptors. Cone size range from 35mm < 67mm (for almost all classical french cars)
Crankshaft for 2CV6. New part. We only import the crankshafts from South America, which are made on
the original tools and with the original materials (this factory produce the 2CV for the South American market). Attention, there are also cheaper crankshafts from China, but we do not offer them for quality reasons.
Crankshaft gear wheel narrowly, for Citroen AMI8 + 2CV6. 22 teeth. Gear-wide: 13,6mm. Wide one
completely: 15,6mm.
- Suitable for this article
Bearing for drive shaft, in gearbox. Suitable for Citroen 2CV6. Dimension: 25 x 52 x 15mm. The
bearing is behind the oil seal. Original SKF. Our bearing has a groove for a circlip, but can also be mounted without.
Bearing gearbox - main shaft front, for 2CV. Original SKF. Measurement: 25x52x15mm, with groove for
retaining ring. Or.Nr.: ZC9620002U
Bearing primary shaft rear, reproduction. Suitable for Citroen 2CV6. Inside diameter: 20mm, outside
e diameter: 52mm, 57mm, overall height: 15mm, depth to stop in the case: 11,5mm. Or.Nr. ZC9620308
Bearing primary shaft, for Citroen 2CV6. Or. No.: 95572590. Reproduction. Dimension: 20x52x57x22mm
Depth gauge to bead seat wreath/ring: 19,00mm.
Bearing flange (ring) for the drive shaft in the wheel hub. Suitable for Citroen 2CV starting from
year of construction 1966, with constant velocity drive shafts. Or.Nr.A37396.
Idling (throttle stop) adjusting screw for Solex carburettors. Suitable for the following
carburettors: 26CBI, 28CBI, 30CBI(AMI6), 26/35PICS, 32PCIS, 34PCIS+PCIS, 34PICS-6
Slow-running jet for oval carburetor. Suitable for 2CV6, Dyane, Ami8, to year of construction
09/1972. Nozzle measurement: 55. For carburetor 26/35 CSIC + 26/35 SCIC.
Steering gear repair set for the tie rod guide. Suitable for Citroen 2CV. Consisting of: Pin + seat
bowls + guides, ball pin, rubber,
Steering worm of 7 teeth, inclusive bearing, for Citroen 2CV. Splines (worm gears) are continuous
up to the bearing. Suitable bush = 12233.
Steering worm of 8 teeth, inclusive bearing, for Citroen 2CV. Good reproduction! The suitable guide
bush down (10mm inside diameter) has our No. 12232. Overall length: 112,8mm.
Steering worm of 8 teeth, inclusive bearing, for Citroen 2CV. Inside diameter: 10mm. Suitable lower
bush = 12232. Overall length: 112,8mm.
Steering worm bearing bush (down at the needle bearing). Suitable for Citroen 2CV. The bearing is a
needle bearing! Only for steering worms with 8 teeth. Inside diameter: 12mm. Outside diameter: 18mm. Overall height: 12mm. Manufacturer SKF.
Steering worm bearing bush 2CV, down at the steering worm. (Needle bearings), manufacturer SKF
Inside diameter 10mm, outside diameter 17mm, height of 12mm
Steering worm bearing bush 2CV, down at the steering worm. (no needle bearing). Inside diameter
10mm, outside diameter 16mm, height of 10mm
Steering worm locking cap down (the cap is hit from downside into the steering gear). 20mm
Suitable for Citroen 2CV.
1728 Articles | Page 18 of 35
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
