for Citroën 2CV Alle
3847 Articles | Page 13 of 77
2CV, Door trim for the rear door, reproduction, made of polished aluminium. The moulding is
supplied with fixing clips. Length: 660 mm, width: 6 mm
2CV, Door trim for the front door, reproduction, made of polished aluminium. The trim are supplied
with clamps. Length: 750 mm, wide ones: 6 mm
2CV, Conversion kit on large luggage compartment hood, suitable for Citroen 2CV. This conversion
kit was in former times an option.
2CV, floorpan plate centrically for the original chassis of Citroen 2CV, Dyane. (semicircular
recess). Made in Europe.
2CV, plastic lining for the rear roof tie bar (at C-support level). Reproduction like original
Made by Franzose. Length 870mm. Or. No. 95593162.
2CV, plastic lining for the front roof tie bar (at B-support level). Reproduction like original
Made by Franzose. Length: 880mm. Or. No. 95595863.
2CV, Reinforcement cross-beam under the seat bench, for Citroen 2CV. This cross-beam is welded
crosswise and the transition to the sheet metal between the wheel housings and the luggage compartment. Made in Germany.
2CV, wind catch on the B-pillar to the rear door. Colour grey. Left + right fitting. For Citroen
2CV up to 1970 (6 symmetrically arranged fastening holes!). This is the rubber (plastic) which is attached to the B-pillar and to the rear door.
2CV, wind catch on the B-pillar to the rear door. Colour black. Left + right fitting. For Citroen
2CV up to 1990. This is the rubber (plastic) which is attached to the B-pillar and to the rear door.
2CV, windbreak, plastic caps (expanding rivet) for fixing the windbreak rubber to the rear door (7
pieces required per side). The expanding rivet also fits the door hinge cover.
2CV, wind catch: Metal strip for attaching the wind catch rubber to the B-pillar. Reproduction like
the original, with a small bend. Suitable for Citroen 2CV. The strip is fixed with 3mm rivets or expanding rivets. Or. No. 3Z 5413825Z
Wind catch, metal strip for the securement wind catch rubber on the door. Suitable for Citroen 2CV
The strip is inside, mounted at the rear doors. Per piece.
2CV, Windshields - ornamental frame, for Citroen 2CV AZAM. The ornamental frame is production from
high-grade steel. Ordered please the connection clip specially!
2CV, Windscreen seal for Citroen 2CV AZAM. The seal is for the mounting of a trim frame! The trim
frame was only mounted on the Belgian 2CV AZAM. Attention: The bonding of the butt edges of the gasket are really bad. But we still offer this rubber, because there are no other rubbers for the AZAM. If you need it, it is better than no rubber!!!
Windshield frame completely, inclusive hood hinge. Suitable for Citroen 2CV. Very good
reproduction, like original. The transition of the corners to the a-post is substantially better, than with the sheet metal 15297. The windshield frame is electrolytically galvanized. Made in Europe.
Windshield frame cross beam down. Suitable for all Citroen 2CV. (Cross beam above the Ventilation
shutter, from the inside seen.) Made in Europe.
2CV, Windshield frame, aluminum strip above at the soft top hood. With this strip the rubber seal
on the windshield frames is clamped.
2CV, windscreen frame, seal under the aluminium rail, at the top of the roof. (Roll-roof seal)
This seal has an additional rubber lip. This means that the aluminium rail is fixed much more securely to the roof. Suitable for Citroën 2CV, built between 1960 and 1990. Part no. A971-80A
2CV, windscreen frame, seal under the aluminium rail, at the top of the roof. This seal is
manufactured in exactly the same way as the original seal used by Citroën. Suitable for Citroën 2CV, built between 1960 and 1990. Or. no. A971-80A
2CV/Dyane, master brake cylinder fixture on the front wall (welds). Suitable for Citroen 2CV +
Dyane. Electrolytically galvanized. Made in Europe.
2CV/Dyane, master brake cylinder bracket: Reinforcement brackets (2 pieces) with the stud bolts
These brackets are mounted from the inside at the connection pedal floor to firewall. Suitable for Citroen 2CV + Dyane. Electrolytically galvanised. Made in Europe.
2CV6, 602ccm, engine gasket set inclusive. Shaft seals and ventil stem sealing. Suitable for
Citroen 2CV6 starting from year of construction 1970 to 1990. Label quality
2CV6, 602ccm. Engine gasket set without shaft seals. For Citroen 2CV6 (to production end) and 2CV4
with 435ccm engine. Label manufactor.
2CV6, tail pipe securement clamp sheet metal. This sheet metal is for the centric rubber fixing at
the chassis. Reproduction from high-grade steel! Or.Nr.AM18284. Made in Germany.
2CV6, tail pipe securement rubber short. This rubber is for the centric securement. Hole spacing
about 60mm. Suitable for Citroen 2CV6. Made in Germany.
2CV6, tail pipe securement rubber long. This rubber is for the rear securement, height of bumper
Hole spacing: about 100m. Length totally: about 111mm. Suitable for Citroen 2CV6. Made in Germany.
2CV6, tail pipe exhaust clip, for Citroen 2CV6 + 2CV4. These clips are pushed over the tail pipe
e and hold the exhaust retaining rubber. Screw connection: M6
2CV6, elbow pipe (S-pipe). Good reproduction. Brand manufacturer from Europe. Without fixing
material! Suitable for Citroen 2CV6 + 2CV4, Dyane, AMI and Mehari.
2CV6, rear muffler locking collar, from high-grade steel. Suitable for Citroen 2CV. (the bracket
locates the rubber to the silencer). Or.Nr.: AM18388. Made in Germany.
2CV6, rear muffler locking collar, made of metal. Suitable for Citroen 2CV. (the bracket locates
the rubber to the silencer). Or.Nr.: AM18388. Made in Germany.
2CV6, rear silencer (long silencer). Good reproduction. Brand manufacturer from Europe. Without
mounting material! Suitable for Citroen 2CV6 + 2CV4, Dyane, AMI and Mehari.
2CV6, rear muffler. Optically as in the seventies Installed. Without mounting material! Suitable
for Citroen 2CV6 + 2CV4. All connection diameters are the same.
3847 Articles | Page 13 of 77
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
