Tie rods slide ring squarely, mounts in the steering gear. Suitable for Citroen 2CV. Reproduction
from a brass alloy. Standard measurement about 8x13x20.
for Citroën 2CV AK-AZU
2539 Articles | Page 44 of 51
Tie rod locking plate, suitable for Citroen 2CV. For tie rod lever with stepped attachment
Installed from year of construction 1963. Or. No.: AM41389. Like the original plates, our locking plates are slightly bent up at the ends. This makes them easier to fold over (securing the screws)
Split pin small, for the tie rod end nut + radius arm bearing. Suitable for Citroen 2CV
Measurement: 2 x 20mm
Tie rod end wrench (630-16/2), for the nut in the tie rod end. Suitable for Citroen 2CV. Note: this
tool do not fit for tie rod end with strengthened nuts.
Tie rod end on the left (only the case, without spring and bearing pans). Suitable for Citroen 2CV
Made one in Germany. Or.Nr.: A44398B. Thread: M14x1,25 left-hand thread
Tie rod end (only the case, without spring and bearing pans). Suitable for Citroen AK400. On the
left + on the right fitting.
Tie rod end on the right (only the case, without spring and bearing pans). Suitable for Citroen
2CV. Made one in Germany. Or.Nr.: A44398C. Thread: M14x1,25 left-hand thread
Tie rod end repair set on the left. Inclusive bearing pan, pressure spring, locking nut, collar
safety sheet. Suitable for Citroen 2CV. Thread: M14x1,25 left-hand thread.
Tie rod end repair set on the right. Inclusive bearing pan, pressure spring, locking nut, collar
safety sheet. Suitable for Citroen 2CV. Thread: M14x1,25 left-hand thread.
Tie rod end locking nut. Suitable for Citroen 2CV. The nut is additionally equipped with a
lubrication nipple. A real improvement!
Tie rod end, 2 x seat bowl + 1 x pressure spring + 1 x crown nut. Complete repair set, in order to
repair the tie rod end inside. High quality. Suitable for all Citroen 2CV, AK, Dyane, AMI.
Spring in the tie rod end. Suitable for Citroen 2CV. Per side 1x spring is required.
- Suitable for this article
Tie rod end collar "Made in European Union", suitable for Citroen 2CV, Mehari, Dyane, AMI. This
collar is produced in Europe for "Der Franzose". The collar is very flexible and can be mounted over the complete tie rod end, without it tears. Better than original!
Dust cap from rubber, for the vent screw at brake calipers and wheel brake cylinders. Universal
suitable for Citroen, Peugeot, Renault.
Dust cap wheel brake cylinder, for piston diameters: 7/8 inch (22,25mm). Suitable for Citroen HY
11CV, 15CV, 2CV. Also universal fitting for other vehicles! Made in France
Plug protection against humidity, made of rubber to wrap around the plug connections, suitable for
2CV, only on the bracket assembly for the headlamps.
Stud bolt M8 x 35. For the securement of the carburetor on the intake manifold. Suitable for
Citroen 2CV6 + 2CV4. (round + oval carburetor). Or. No. 26 161 509
Stop sleeve for the clutch cable (2CV to year of construction 1967, with diagonal clutch release
fork lever) and for the hand brake cables drum brake. Or. No. A454-76.
Shock absorber short, suitable for Citroen AK in front + rear, AMI 6 + 8 for in front and rear
ACDY only in front! (per piece). 14mm securement eye. Note: There are also Ami 6 vehicles, which are equipped shock absorbers with 12mm shock absorber in front, and rear 14mm. Then please, select for in front shock absorbers the number 12319 . Manufacturer "Record France". Length when pushed together: 335 mm. Length when pulled apart: 495 mm.
Valve push rod tube for 2CV4 (425ccm engine). Length totally: 165mm, diameter 16mm, fit (set off)
at the cylinder head: 15mm.
2539 Articles | Page 44 of 51
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
