Square switch with chrome frame. The switch also has an indicator light (bulb base Ba9s). Universal
switch for e.g. heater blowers, additional consumers.... Dimensions: 36x18mm (French standard size). Suitable for Peugeot, Citroen, Renault.
for Renault Alle
3411 Articles | Page 59 of 69
Switch for the reversing lamp. Suitable for Renault R4, R5, R6, R16. Thread: M16 x of 1,0. 2
electric plug contacts.
Discs (windscreen) Pull-in tool (cord with handle). This is used to pull the rubber lip of the seal
over the sheet metal fold. Very helpful!
Windscreens (windscreen) piping assembly tool - bracket inserts. For small piping. There are 5
brackets in different widths so that narrow and wide piping can be fitted (e.g. for the 2CV, R4....). Suitable for tool with item number 20134.
Windscreen Installation Tool Set. Windshield sealing trim assembly tool. With this tools will the
rubber lip (seal) inclination (spread) and it can fit the sealing trim at the same time. Attention: The tool is for very wide piping. For chrome piping e.g. Citroen 2CV, Renault R4 etc. small brackets must be fitted. See our item number 20137.
Permanently elastic window sealant. Original Teroson! 75ml tube. Application : Ideal for sealing
rubber-mounted front, rear and side windows. Very stable, water resistant, remains elastic. Good adhesion even on damp windscreens.
Vehicle Window sealant permanent elastic. Original Teroson! Cartouche 310ml. Application: Ideally
to sealing rubber-mounted front. - Tail and side windows. Very stably, water-resistant, remains elastic. Good adhesion also on wet disk.
Windscreen washer reservoir - plastic bag with integrated electric water pump. 12 volts. The
reservoir is supplied with mounting and accessories and can be installed in any vehicle, e.g. Citroen Mehari, Renault R4 first versions, etc. This type of windscreen washer reservoir has also been installed in many Italian vehicles (Alfa Romeo Spider...).
Washer reservoir electrical with built-in set for 2CV and other classical cars. Complete with
h push-button, cable, cross bars etc. very practical and small. Width 19,5cm, height of 16,5cm, depth 5,5cm
Washer reservoir with integrated, electrical water pump. 12 V. Capacity: 1.2 L. width: 122mm
overall height totally: 185mm. Building depth altogether: 100mm. The reservoir is supplied with fixture. The fixture is from the rear at the reservoir.
Windscreen washer reservoir with integrated electric water pump. 12 volt. Suitable for Renault R4
R5, R6, R7, R12. Corresponds to original number: 7700628056
Washer reservoir, suitable for Renault R4, R16. Original Renault, no reproduction. The reservoir is
supplied without lid. Or. No. 77.04.000.003
Wiper nozzle synthetic grey. Universal fitting. 4mm hose connection. The wiper nozzle is locked
with a nut from rear. 1 water jet. Low body height. Mounting diameter: 8,0mm.
Windscreen washer nozzle black. Universal fitting. 4mm hose connection. The washer nozzle is
screwed with a nut from behind. 2x water jet. Flat design.. Mounting diameter: 8,0mm.
Washer pump electrical. 12 V. Very stable version with galvanized metal fixture. 2x flat plug
connection from above! Made in the European Union. The picture indicates the correct mounting position. The pump section is down, the electric motor above!
Washer pump, electrically, color black. Suitable for Citroen DS. This pump is to be used also very
well for conversion, e.g. 2CV, Dyane, Peugeot, Renault. Note: The pump is not self-priming. The water must run (from alone) inside. Outlet water = power connection side. If the pump works more than 15 seconds without water, it is broken.
Windscreen washer foot pump seal. This is the seal that is fitted under the foot pump (seal to the
floor pan). Suitable for Citroen 2CV up to the year of construction 1970 (depending on country of delivery). Citroen Dyane, Acadyane. Renault R4 + R16.
Foot switch for the disk wiping water! Suitable for Renault R4 + R16. Or. No. 7701002908. Original
no reproduction. Fixing bolts center - center: 67mm. Note: The pump have only 1 line connection.
Foot-operated pump set for windschield wiper fluid. Consisting of foot pump, 2 return flow
stoppers, 1x T-valve, 3 meters hose. Assembly: Starting from the foot pump with the T-valve, 1x to the reservoir (place the valve in such a way that the water from the reservoir can pass through) and 1x to the windshield washer nozzle (valve lets the water pass in the direction of the nozzle). The flow directions are marked with an arrow on the valve. Assembly instruction online in the shop.
PDF FILE Disk washing water hand pump, reproduction, 5mm. This pump is mounted in the dashboard. In
addition, the pump is a reproduction of the first version, and can installed into a Citroen 2CV6 and partial in a Renault R4 .
Windscreen washing water hand pump. Reproduction, completely with sheet metal holder for a later
mounting! Suitable for Citroen 2CV. In addition, the pump can be universal installed.
Headlamp mounting bolt (stud bolt with ball). Dimension: 5 x 36mm. Thread: M5. Universal suitable
for many French vehicles.
Headlight reflector (without glass). Headlight system "Cibie 160mm". Quality finishing. This can be
used to repair the original headlight. Simply loosen the glass cleanly (the old reflector can be damaged) and glue it to the new reflector. Suitable for Renault: 4CV, Dauphine, R4, Estafette, R8, R10.....
Headlight reflector (without glass). Headlight system "Cibie 180mm". The reflector has an outer
diameter of 190mm, but is suitable for a lens with 180mm diameter. Quality reproduction. The original headlight can be repaired with this. Simply remove the glass cleanly (the old reflector may be damaged for this) and glue it onto the new reflector. Suitable for Renault: Floride, Caravelle, Fregate, R8 Gordine. Peugeot 203, 403, 505, Citroen DS up to 1967.
Universal protective rubber (e.g. for protecting electric cables, brake lines, brake hoses
handbrake cables, speedometer cables, petrol hose... External dimensions: 23x30mm. Inner diameter: 8mm. The rubber is slit on one long side, and can therefore be easily placed over the cable to be protected!
Universal protective rubber (e.g. for protecting electric cables, handbrake cables, petrol hose
External dimension: 42mm. Length: 31mm. Inner diameter: 12mm. The rubber is not slit (but of course this can be done afterwards if it makes assembly easier)
Tube bending sleeve. Suitable for hose outer diameter of 12,5 > 13,4mm. Length: 60mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Tube bending sleeve. Suitable for hose outer diameter of 14,6 > 16,4mm. Length: 65mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Tube bending sleeve. Suitable for hose outer diameter of 16,5 > 18,4mm. Length: 70mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Tube bending sleeve. Suitable for hose outer diameter of 18,8 > 21mm. Length: 75mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Tube bending sleeve. Suitable for hose outer diameter of 21,8 > 24mm. Length: 90mm. With this you
can easily produce bent water hoses. Simple and ingenious!
Hose clamp 11-17mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 13-20mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 15-24mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 19-28mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 22-32mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 26-38mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 32-44mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 38-50mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 40-56mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 50-65mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
Hose clamp 57-75mm, especially for radiator hose. Vintage look. Embossed band with raised edges
This prevents the hose from being damaged. Small screw housing with 7mm hexagon head screw (with slot). Normal, modern hose clamps squeeze the hose. This is completely avoided with these clamps. And they even look better.
3411 Articles | Page 59 of 69
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
