Tie rods slide ring squarely, mounts in the steering gear. Suitable for Citroen 2CV. Reproduction
from a brass alloy. Standard measurement about 8x13x20.
for Citroën 2CV 2CValt
1720 Articles | Page 31 of 35
Split pin small, for the tie rod end nut + radius arm bearing. Suitable for Citroen 2CV
Measurement: 2 x 20mm
Tie rod end wrench (630-16/2), for the nut in the tie rod end. Suitable for Citroen 2CV. Note: this
tool do not fit for tie rod end with strengthened nuts.
Tie rod end, 2 x seat bowl + 1 x pressure spring + 1 x crown nut. Complete repair set, in order to
repair the tie rod end inside. High quality. Suitable for all Citroen 2CV, AK, Dyane, AMI.
Spring in the tie rod end. Suitable for Citroen 2CV. Per side 1x spring is required.
- Suitable for this article
Tie rod end collar "Made in European Union", suitable for Citroen 2CV, Mehari, Dyane, AMI. This
collar is produced in Europe for "Der Franzose". The collar is very flexible and can be mounted over the complete tie rod end, without it tears. Better than original!
Dust cap from rubber, for the vent screw at brake calipers and wheel brake cylinders. Universal
suitable for Citroen, Peugeot, Renault.
Dust cap wheel brake cylinder, for piston diameters: 7/8 inch (22,25mm). Suitable for Citroen HY
11CV, 15CV, 2CV. Also universal fitting for other vehicles! Made in France
Stop sleeve for the clutch cable (2CV to year of construction 1967, with diagonal clutch release
fork lever) and for the hand brake cables drum brake. Or. No. A454-76.
26 long nut, for the original shock absorber pin. Suitable for Citroen 2CV. Original one, our shock
absorber pin 12066 is fastened with a 27mm key!
Valve push rod tube for 2CV4 (425ccm engine). Length totally: 165mm, diameter 16mm, fit (set off)
at the cylinder head: 15mm.
Follower tubing seal - sheet metal plates, for Citroen 2CV to year of construction 1972. Suitable
for the follower tubing seal with wide connecting post. Per piece!
Valve push rod tube seal for 2CV (old version). Single seal, without bar in the center. You need 4
pieces per car. Manufacturer: Original Glaser, no reproduction.
Bumper rear for Citroen 2CV. Low version. Installed from year of construction 06/1963 to 1974. The
bumper is delivery without adhesive strip (16510). The bumper is primed beige and should be painted. Made in Europe.
Bumper rear for Citroen 2CV6 + 4, high (11cm) version! Installed from year of construction 09/1974
to 07/1990. The bumper is delivered without black adhesive strips (16537). The bumper is primed beige and should be painted. Made in Europe.
Bumper rear, first version. "CITROEN" emblem (signature), which is mounted between the two trims
The signature is out of sheet metal. Installed at Citroen 2CV up to year of construction 1961. Also partly at Citroen 11CV + HY.
Bumper rear, first version. Suitable for Citroen 2CV, of year of construction 1952 to 1963. The
bumper should be painted!
Bumper adhesive strip narrowly. Color black. Measurements of 1490x30mm. Suitable for 2CV bumper in
front, Installed from 09/1974 to 1990. The adhesive strip fits also for the rear, narrow (9cm highly) bumper.
Bumper in front, first version. Suitable for Citroen 2CV to year of construction 06/1963. The
bumper is supplied without bumper overriders. The bumper should be painted. Made in Europe.
Bumpers rubber grey rear, for Citroen 2CV. This rubber was mounted starting from 1963 to about 1975
instead of black adhesive strips and fits only on the low (7,6cm) high bumper.
Bumpers rubber grey, in front, for Citroen 2CV. This rubber was mounted starting from 1963 to 1975
instead of black adhesive strips.
Bumpers rubber black rear, for Citroen 2CV. This rubber was mounted starting from 1963 to about
1975 instead of black adhesive strips and fits only on the low (7,6cm) high bumper.
Bumpers rubber black, in front. For Citroen 2CV. This rubber was mounted starting from 1963 to
1975, instead of black adhesive strips.
Bumper trim rear, on the left + on the right fitting., for Citroen 2CV to year of construction
1963. (Aluminum rail with grey rubber). Length about 550mm. The trim is required 2x per car. The suitable fixing clip has the number 16844.
Bumpers trim in front centrically, for Citroen 2CV to year of construction 1963. (Aluminum rail
with grey rubber). Length about 460mm. The trim is required 1x per car. The suitable fixing clip has the number 16844.
Bumpers trim in front, on the left + on the right fitting., for Citroen 2CV to year of construction
1963. (Aluminum rail with grey rubber). Length about 325mm. The trim is required 2x per car. The suitable fixing clip has the number 16844.
Front bumper brackets (AZAM brackets). 1 set (2 pieces), fits all Citroën 2CV models from 1963
onwards. These brackets were fitted to the luxury 2CV models in the 1960s and 1970s!
Bumper mounting bracket rear, for Citroen 2CV6 + 4. The bracket is for the low (9cm) bumper
Installed from 1963 to 09/1974. Made in Europe.
Bumper mounting bracket in front on the right. Suitable for Citroen 2CV + AZU, of year of
construction 1948 to 1965. Or. No. A815-91C
1720 Articles | Page 31 of 35
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
