The headlamp is for a later mounting underneath the bumper! It cannot be used as substitute for the original backup lights from R4! Lampholder for the bulb: Ba15s. Maximum 21Watt. (Our number 14035 + 14045).
improvement for classic vehicles that use a hand pump without a ball valve to deliver water. This ensures that windscreen washer fluid is always available at the spray nozzles. Please note the direction of flow during installation! It also prevents petrol from flowing back in the fuel line (useful for longer periods of inactivity). Please install this valve close to the petrol pump (between the petrol pump and the tank).
E") 1 thread light, only brake or taillight! With metal base + support! The glass has 68,5mm diameter! Used in HY, AZU, DS - in many Renault + Peugeot models as well!
Peugeot J7. The rear lights have an "E" approval mark!
UP, J7. Fits on the left + on the right.
were used in many French cars!
classic cars. Diameter: 56mm.
for Citroen 2CV, DS, HY, SM, GS, CX, Peugeot
button and not a toggle switch. The push button is useful for electric windscreen washers, horns or headlight flashers, for example. Dimensions: 36x18mm (French standard size). Suitable for Peugeot, Citroen, Renault.
switch for e.g. heater blowers, additional consumers.... Dimensions: 36x18mm (French standard size). Suitable for Peugeot, Citroen, Renault.
Peugeot 504. Or. No. 2454.55
20mm. Outer diameter centre: 17mm. Inner diameter: 10mm. Total length: 16mm.
Peugeot 204, 304, 404, 504. Inside diameter: 12mm. Outside diameter: 19mm. Or. No. 2445.09
over the sheet metal fold. Very helpful!
brackets in different widths so that narrow and wide piping can be fitted (e.g. for the 2CV, R4....). Suitable for tool with item number 20134.
rubber lip (seal) inclination (spread) and it can fit the sealing trim at the same time. Attention: The tool is for very wide piping. For chrome piping e.g. Citroen 2CV, Renault R4 etc. small brackets must be fitted. See our item number 20137.
rubber-mounted front, rear and side windows. Very stable, water resistant, remains elastic. Good adhesion even on damp windscreens.
to sealing rubber-mounted front. - Tail and side windows. Very stably, water-resistant, remains elastic. Good adhesion also on wet disk.
reservoir is supplied with mounting and accessories and can be installed in any vehicle, e.g. Citroen Mehari, Renault R4 first versions, etc. This type of windscreen washer reservoir has also been installed in many Italian vehicles (Alfa Romeo Spider...).
h push-button, cable, cross bars etc. very practical and small. Width 19,5cm, height of 16,5cm, depth 5,5cm
overall height totally: 185mm. Building depth altogether: 100mm. The reservoir is supplied with fixture. The fixture is from the rear at the reservoir.
with a nut from rear. 1 water jet. Low body height. Mounting diameter: 8,0mm.
screwed with a nut from behind. 2x water jet. Flat design.. Mounting diameter: 8,0mm.
construction 1961. Also suitable for many classical Peugeot. (403). Bore for the nozzle must be 8-9mm.
connection from above! Made in the European Union. The picture indicates the correct mounting position. The pump section is down, the electric motor above!
well for conversion, e.g. 2CV, Dyane, Peugeot, Renault. Note: The pump is not self-priming. The water must run (from alone) inside. Outlet water = power connection side. If the pump works more than 15 seconds without water, it is broken.
505, 604. Or. No. 643422
stoppers, 1x T-valve, 3 meters hose. Assembly: Starting from the foot pump with the T-valve, 1x to the reservoir (place the valve in such a way that the water from the reservoir can pass through) and 1x to the windshield washer nozzle (valve lets the water pass in the direction of the nozzle). The flow directions are marked with an arrow on the valve. Assembly instruction online in the shop.
mounting! Suitable for Citroen 2CV. In addition, the pump can be universal installed.
for many French vehicles.
PDF FILE 
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
