for Peugeot Alle
3051 Articles | Page 37 of 62
P 404, clutch release yoke, for hydraulic clutch. Suitable for Peugeot 404 Diesel, starting from
year of construction 1967. Peugeot 305, 309, 405. Citroen C15, Citroen BX 19, starting from 1987. Or. No. 2117.42
P 404, clutch master cylinder. Suitable for Peugeot 404. Piston diameter: 19,05mm. Connection
M12x1. Distance of the fixing hole: 50mm. Or. No. 2095.11. Made in Europe.
P 404, crankshaft bearing, standard dimension. Suitable for Peugeot 404, before year of
construction 1970. Only for engine: XC5 (5 crankshaft bearings).
P 404, crankshaft bearing, oversize 0,30. Suitable for Peugeot 404, before year of construction
1970. Only for engine: XC5 (5 crankshaft bearings).
P 404, steering gear (new part). Suitable for Peugeot 404, to year of construction 1973. The
steering gear is supplied without tie rods. Before assembly, please grease the steering gear (ca.60g).
P 404, steering column cover, suitable for Peugeot 404 Coupe + Cabrio! Note: Casting of a used
well preserved lining! Produces in complex manual work. Not perfectly, but substantially better than the most Installed linings!
P 404, air filters. Suitable for Peugeot 404, starting from year of construction 03/1968
Corresponds to PURFLUX A172. Height: about 130mm. Outside diameter: about 118mm. Inside diameter: 84mm. Or. No. 1445.29
P 404, air hose between carburettor + air filter (bent hose 180°, without additional connection)
Suitable for Peugeot 404.
P 404, suspension strut sleeve (bellows on the shock absorber). Suitable for Peugeot 404 (1
assembly, 90mm) up to the year of construction 1964! Or. No. 5254.02
P 404, clutch disk. Suitable for Peugeot 404 Cabrio + Coupe, starting from year of construction
1967. Dimension: 215 x 142 x 3,2mm. Hub profile: 29,4mmx24,5mm. 10 teeth.
P 404, front lower cross member. Suitable for Peugeot 404 with petrol engine (sedan, convertible
coupe, pick-up). Or. No. 7103.12
P 404, wheel suspension repair set in front (wishbones), per side. Suitable for Peugeot 404
Consisting of: Rubber block squarely with 24mm bore, 1x bush 29x32mm, 2x bush 16mm inside diameter - outside diameter 25 x 30mm - length 17mm, 1x bonded-rubber bushing 16mm inside diameter - outside diameter 34mm - length 41,5mm. The pin has 14mm diameter.
P 404, wheel suspension repair set in front, per side. Suitable for Peugeot 404. Consisting of: 1x
bush inside diameter 12 x 34mm - outside diameter 28 x 32mm. 2x bush inside diameter 16mm - outside diameter 25 x 30mm - length 17mm, 1x bush largely inside diameter 12 x 50mm - outside diameter 32 x 34mm. 2x pin 12mm diameter.
- Suitable for this article
P 404, wheel brake cylinders rear on the left. System Bendix. Piston diameter: 20,64mm. Connecting
thread: 3/8 x 24UNF. Mounting board bore: 35,7mm. Construction length: 70mm. Suitable for Peugeot 404, all models Saloon. Of year of construction 10/1967 to 05/1968. 404 all Thermostable Saloon, from 1966 to 10/1969. 404 models USA, starting from 1966. Or. No. 4402.22, Made in Europe.
P 404, wheel brake cylinders rear on the right. System Bendix. Piston diameter: 20,64mm. Connecting
thread: 3/8 x 24UNF. Mounting board bore: 35,7mm. Construction length: 70mm. Suitable for Peugeot 404, all models Saloon. Of year of construction 10/1967 to 05/1968. 404 all Thermostable Saloon, from 1966 to 10/1969. 404 models USA, starting from 1966. Or. No. 4402.23, Made in Europe.
P 404, wheel brake cylinders in front (on the left + on the right are identically constructed)
Suitable for Peugeot 404, with Hydrovac brake assembly (thermostable). Piston diameter: 34,92mm. Overall length: 82mm. Brake line connector: 3/8 x 24 UNF. Distance of the fixing bolts: 44mm. With vent screw! Or. No. 4401.30. Made in France
P 404, wheel brake cylinders in front (on the left + on the right are identically constructed)
Suitable for Peugeot 404, with Hydrovac brake assembly (thermostable). Piston diameter: 34,92mm. Overall length: 82mm. Brake line connector: 3/8 x 24 UNF. Distance of the fixing bolts: 44mm. Without vent screw! Made in France
P 404, set (13x) spring washers "Belleville" in the steering gear, for the left tie rod. Suitable
for Peugeot 404. Or. No. 3839.02
P 404, shift linkage repair set (for the shift linkage at the steering column). Suitable for
Peugeot 404, starting from year of construction 10/1967.
P 404, shift linkage repair set, for the steering columm gear shift change. Suitable for Peugeot
404, to year of construction 1967.
P 404, box sills - reinforcement. The reinforcement fits on the left + on the right. Per piece
Suitable for Peugeot 404 Cabriolet. Made in European Union.
P 404, sill panel left (not the panelling of the sill), with all beads and indentations. Suitable
for Peugeot 404 saloon. Good reproduction of the original.
P 404, sill panel right (not the panelling of the sill), with all beads and indentations. Suitable
for Peugeot 404 saloon. Good reproduction of the original.
P 404, bonded-rubber bushing A-arm. Suitable for Peugeot 404. Inside diameter: 12mm. Outside
diameter: 32mm. Length inside: 50mm. Length outside: 34mm. Or. No. 3561.04
P 404, bonded-rubber bushing for the wishbone. Suitable for Peugeot 404. Inside diameter: 12mm
Outside diameter: 28mm. Length inside: 38mm. Length outside: 32mm. Or. No. 3523.09
3051 Articles | Page 37 of 62
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
