for Peugeot Alle

P 504/505/C25/J5, rear wheel bearing set. Outer diameter: 90mm. Inner diameter: 40mm. Width: 25mm

Suitable for Peugeot 504 Pick Up from year of construction 07/1981 to 02/1994. 504 GR Pick Up from 08/1990 to 10/1999. Peugeot 505 Break (04/1982 > 11/1995). Peugeot J5 (09/1990 > 03/1994). Citroen C25 (07/1981 > 02/1994). Or. No. 3326.28 + 3334.31 + 3325.52 + 3325.50. Citroen 9403221108

P 504/505/J5, engine gasket set (inclusive cylinder head gasket). Suitable for Peugeot 504, 505

J5. Fuel engines: XN1, XNA, XN2 starting from year of construction 1970. The sealing set is without water pump seal!

P 504/505/J5/C25, intake manifold seal for Peugeot 504, 505, J5. Citroen C25. Engines: Petrol

carburetor + injection engines. 1,8L + 2,0L. Engine code 169 (XM7T). Or. No. 0348.33

P 504/505/J5/C25, piston + liner (4 pieces), suitable for Peugeot 504, 505, J5, Citroen C25. For

engine: XN1, XN1P, XN1T/2. bore: 88mm. Piston pin: 23 x 74mm. Piston rings: 1,5 - 2.0 - 4,0mm. Dimensions of the liner = outside diameter down: 93mm. Height totally: 136,20mm. Outside diameter above: 101,90mm. Height from downside to bulge (base) of the liner: 99,10mm.

• Suitable for this article
• 
  Piston ring compressor, 60 to 90mm clamping range. Hobby version (not for daily
  16,76 €

P 504/505/J5/C25, air filter. Suitable for Citroen C25 (1,8E + 2,0E), of year of construction

09/1981 to 03/1994. Peugeot 504. Peugeot 505 (1.8 + 2.0), starting from year of construction 11/1980. Peuegot J5, starting from year of construction 01/1983. Outside diameter: 130mm. Inside diameter: 91mm. Height: 160mm. Or. No. 1445.63

P 504/505/J5/C25, cylinder head gasket for Peugeot 504,2,0. J5, J7. Citroen C25. Oversize +0,4mm

Suitable for engine XN1, XN2, XNA. Installed from year of construction 09/1970 to 09/1983. Or. No. 0209F4

P 504/505/J5/C25, cylinder head screws (10 pieces). Suitable for Peugeot 504, 505, J5, Citroen C25

Petrol engines from 1,6L to 2.0 liters engine capacity. Thread: M12x1,5. Length: 179mm. Or. No. 0204.51.

P 504/505/J5/J9. Piston ring set (for 1 piston), for XN1 engine (4 liners) + ZNJK engine (6

liners). Bore: 88mm. Piston rings: 1,5mm + 2,0mm + 4,0mm. Suitable for Peugeot 504 (4 liners + 6 liners), Peugeot 505, J5, J9.

• Suitable for this article
• 
  piston ring presenting pliers for diameter 40-100.
  22,71 €
• 
  Piston ring compressor, 60 to 90mm clamping range. Hobby version (not for daily
  16,76 €

P 504/505/J7, cylinder head gasket. Suitable for Peugeot 504 2,3D. Peugeot 505 2,3D. J7 2,3D

1,53mm heavily. 2 grooves. Or. No. 0209.55

P 504/505/J7/HY, exhaust elbow seal, suitable for Indenor Diesel XDP88. Bore 94mm. Suitable for

Citroen HY Diesel. Peugeot 504D, 505D, J7D, J9D. Inside diameter: 40 x 30mm. Bore diameter: 9mm. Bore distance from center to center: 64mm.

P 504/505/J7/HY, intake manifold seal for Indenor Diesel XDP88. Bore 94mm. Suitable for Citroen HY

Diesel. Peugeot 504D, 505D, J7D, J9D.

P 504/505/J7/J5/25, piston + liner (4 item). Suitable for Peugeot + Citroen C25. Engine: XM7T 169B

Bore: 84mm. Engine capacity: 1796cc. Piston rings: 1,5mm + 2,0mm + 4,0mm. Piston pin 23x70mm. Outside diameter down: 93mm. Outside diameter above: 99,2mm. Height totally: 136,2mm.

• Suitable for this article
• 
  Piston ring compressor, 60 to 90mm clamping range. Hobby version (not for daily
  16,76 €

P 504/505/J7/J9, generator. Suitable for Peugeot J7, J9, 505, 504. (Petrols with carburetor). 50A

Single swivel arm. Direction of rotation in in the clockwise direction. With intergrierten control device.

Carburetor repair set Peugeot 504, 505, Talbot Tagora. Carburetor Solex 32/35 TMIMA + 32/35 MIMSA.

• Suitable for this article
• 
  Nozzle gauge from 0.45 to 1.5 mm. 20 nozzle gauges. With these nozzle gauges
  13,78 €
• 
  Carburettor jet cleaning tool. Essential for carburettor maintenance and
  10,81 €

P 504/604, drive shaft collar, gearbox side (with sheet metal casing). Suitable for Peugeot 504 +

604. Connections: 82,6 + 26,7mm. The metal casing is 95mm long. Or. No. 3293.55

caliper repair set Peugeot 504-604 System ATE, brake piston 54mm

P 504/604, brake disk set in front. Diameter: 273mm. Heavy one: 12,7mm. Snap diameter: 76mm. 4

hole. Suitable for Peugeot 504, 505, 604. Or. No. 4246.42 + 4246.84

P 504/604, window lifter door on the left. For Peugeot 504 sedan (the window lifter fits for the

front and rear door). For Peugeot 604 (only rear door). Or. Nr. 9221.25

P 504/604, window lifter door on the right. For Peugeot 504 sedan (the window lifter fits for the

front and rear door). For Peugeot 604 (only rear door). Or. No. 9222.24

P 504/604, Steering sleeve (for power steering), small opening.. Per piece. Oval opening 65/50mm

Opposite opening: 18mm. Total length, compressed: 120mm. Or. No. 4066.10. The power steering normally has a sleeve with a large and one with a small opening.

• Suitable for this article
• 
  P 504/505/604, steering sleeve (power steering). Large opening. Suitable for
  8,83 €

P 504/604, collar for the steering column (power steering). Suitable for Peugeot 504 + 604. Or. No

4066.16

P 504/604, oil filter for the automatic transmission. Suitable for Peugeot 504 V6 (Cabrio + Coupe)

Peugeot 604 V6. Or. No. 2263.09. Original Peugeot, no reproduction (NOS)

P 504/604, plastic seal (50mm long), for the chrome sheet metals on the box sill. Suitable for

Peugeot 504 + 604. Or. No. 9066.11. Original Peugeot, no reproduction.

P 504/604, Repair set (rubbers) for rear brake caliper. Brake system Lucas. For piston diameter

43mm (floating caliper - disc brake). The hole in the dust boot has 20mm diameter. Suitable for Peugeot 504, 505 + Peugeot 604.

• Suitable for this article
• 
  P 504, piston for rear brake caliper. Brake system: Lucas. Suitable for Peugeot
  46,76 €
• 
  P 504, piston for rear brake caliper. Brake system: Lucas. Suitable for Peugeot
  57,17 €

P 504/604, 5-speed gear knob, suitable for Peugeot 504 (convertible, coupé + saloon). Peugeot 604

Or. No. 2403.31

P 504/604, gear shift knob, suitable for 504, 604, 505. 4 gear gearbox

P 504/604, bonded-rubber bushing for the wishbone front axle. Suitable for Peugeot 504, of year of

construction 07/1968 to 02/1971. Peugeot 604, of year of construction 09/1979 to 05/1983. Inside diameter: 16,0mm. Outside diameter: 38,0mm. Length inside: 41,5mm. Length outside: 41,4mm. Or. No. 356106.

P 504/604, bonded-rubber bushing, for the wishbone front axle. Suitable for Peugeot 504, starting

from year of construction 1974. Peugeot 604. Inside diameter: 14mm. Outside diameter: 33mm. Length inside: 44mm. Length outside: 32mm. Or. No. 3523.16

P 504/604, tie rod end (fits on the left or on the right). For Peugeot 504, to year of construction

12/1979. Peugeot 604. Thread: M14x1,5 Made in Italy

P 504/604, fuel filler cap lockable, exclusively suitable for Peugeot 504 V6 (Cabrio + Coupe)

Peugeot 604 V6. Not suitable for Peugeot 2,0l (4 liners)!

P 504/604/505, gear shift linkage rubber bushing. Suitable for Peugeot 504, Peugeot 604, 505

Gearbox: BA7, 4 gear. Or. No. 2415.25

P 504/604/505/Talbot Tagora, wheel bearing kit, rear, size: 42x84x36

P 504/604/R30, exhaust elbow seal. Suitable for Peugeot 504 V6 + 604 V6. Renault R30 + Alpine A310

V6. Inside diameter: 3 x 35mm. Bore diameter: 12 x 8,0mm + 3 x 9,0mm. Or. No. 0349.28

P 504/604/R30, intake manifold seal. Suitable for Peugeot 504 V6, 604 V6. Renault R30 + Alpine A310

V6. Or. No. 0348.25

P 504/604/R30, valve cover gasket on the left (made of rubber, approx. 2 mm thick). Suitable for

Peugeot 504 V6 (Cabriolet + Coupe), 604 V6. Renault R30, Alpine A310 V6. Or. No. 0249.29

P 504/604/R30, valve cover gasket on the left (made of paper, approx. 1 mm thick). Suitable for

Peugeot 504 V6 (Cabriolet + Coupe), 604 V6. Renault R30, Alpine A310 V6. Or. No. 0249.37 + 0249.64

P 504/604/R30, valve cover gasket on the right (made of rubber, approx. 2 mm thick). Suitable for

Peugeot 504 V6 (Cabriolet + Coupe), 604 V6. Renault R30, Alpine A310 V6. Or. No. 0249.30

P 504/604/R30, valve cover gasket on the right (made of paper, approx. 1 mm thick). Suitable for

Peugeot 504 V6 (Cabriolet + Coupe), 604 V6. Renault R30, Alpine A310 V6. Or. No. 0249.31 + 0249.66

P 504/604/R30/Alpine V6. Engine gasket set (inclusive cylinder head gasket + shaft seals). Suitable

for Peugeot 504 V6 (Cabriolet + Coupe). Peugeot 604 V6. Renault R30 V6. Renault alpine A310s V6. For engine capacity: 2646ccm. Or. No. 0197.75

P 504/604/Talgora, rear brake pads, original equipment quality (with wear indicator). Lucas

Girling braking system. Suitable for Peugeot 504 + 604. Talbot Talgora. Dimensions: Height = 55.2 mm. Width = 68.3 mm. Thickness: 16.4 mm. Or. No. 425008, 425073, 425007.

P 504/604/Talgora, rear brake pads, reproduction (with wear indicator). Lucas-Girling braking

system. Suitable for Peugeot 504 + 604. Talbot Talgora. Dimensions: Height = 55.2 mm. Width = 68.3 mm. Thickness: 16.4 mm. Or. No. 425008, 425073, 425007.

P 504/605/505, Front wheel bearing set. Suitable for Peugeot 504, from 06/1969 to 09/1993. Peugeot

505 from 05/1979 to 12/1990. Peugeot 604 from 03/1976 to 12/1986. Talbot Tagora from 07/1980 to 12/1984. Dimension bearing 1: 47 x 25 x 15mm. Bearing 2: 58 x 32 x 17mm. Or. No. 3748.09

P 504/A110, interior light cap. Suitable for Peugeot 504 Coupe. Or. No. 6365.08. Renault Alpine

A110, late years of construction. For Alpine A110, be sure to compare the interior light caps exactly.

P 504/CX, generator (with integrated battery charging regulator). Suitable for Peugeot 504 V6

(Coupe + Cabrio). Citroen CX 2000, starting from year of construction 1979. 12 V. 70 ampere, double arm. Assembly position: 20°.

P 504/J5, radiator suitable for Peugeot 504 D (1.9 + 2,1L), Installed starting from year of

construction 1982. Peugeot J5 Diesel, starting from year of construction 10/1983. 825mm lengthens. Wide 415mm. Deep 32mm.

P 504/J5/J9. Piston ring set (for 1 piston), for XDP 4,90 Diesel engine. Bore: 90mm. Piston rings

2,0mm + 2,0mm + 2,0mm + 4,5mm. Suitable for Peugeot 504, J5, J9.

• Suitable for this article
• 
  piston ring presenting pliers for diameter 40-100.
  22,71 €
• 
  Piston ring compressor, 60 to 90mm clamping range. Hobby version (not for daily
  16,76 €

P 504/R21, brake shoe set rear. For drum diameters: 255mm. Wide one: 45mm. Suitable for Peugeot 504

Renault R21.

P 504C, cover (frame) in brown, for the belt duct in the parcel shelf. Suitable for Peugeot 504

Coupe, from year of manufacture 1979. Or. No. 8341.74

P 504C, cover in brown, for the operation of the 3-corner window in the door. Suitable for Peugeot

504 convertible + coupe, from 1975 model year. Or. No. 9280.11

P 504C, cover in black, for the operation of the 3-corner window in the door. Suitable for Peugeot

504 convertible + coupe, from 1975 model year. Or. No. 9280.08