Heater hose connection connecting piece (large, with flap), centrically (welded at the front wall)
Suitable for Citroen 2CV6 RHD (right hand drive). Made in Europe.
heating and ventilation for Citroën 2CV 2CV6
79 Articles | Page 1 of 2
Heater hose connection connecting piece (large, with flap), centrically (welded at the front wall)
Suitable for Citroen 2CV6. Made in Europe.
Heater hose connection connecting piece (small) on the right (welds at the front wall). Suitable
for Citroen 2CV6. Made in Europe.
Ventilation shutter seal rubber, for Citroen 2CV, all models. This rubber is a quality after
production, and corresponds to the original rubber.
Ventilation shutters rubber seal (foam rubber), self adhesive, under the Ventilation shutter, at
the body. Suitable for Citroen 2CV.
Ventilation shutter completely (original), for Citroen 2CV. The Ventilation shutter is supplied
with seal and trim! The Ventilation shutter must paint before be adapted! Original Citroen, no reproduction!
Ventilation shutter completely, for Citroen 2CV. Reproduction out of sheet metal. The Ventilation
shutter is supplied with seal and trim! The Ventilation shutter must be adapted at the vehicle, before it is painted.
Ventilation shutter aluminum strip, 2CV. The strip is a little more matte than the original. 12x
nut M3 (20166) are required!
Ventilation shutter trim from polished high-grade steel, suitable for Citroen 2CV. Own
reproduction. 12 x nut M3 are required. (20166)
2CV, ventilation flap, re-fitting grid for air distribution towards the driver. This ingenious
little grid redirects the airflow towards the driver when the ventilation flap is open. The grid is fitted within couple of minutes, using the clips supplied. So: ventilation system variable according to speed! We wouldn't want to do without it at high temperatures!
PDF FILE Ventilation shutter, pin for Ventilation shutter linking (without clamp), Citroen 2CV, for all
years of construction. Diameter: 5,0mm
Securing clip suitable for the Ventilation shutter, for Citroen 2CV. (Securement installing
handwheel at the Ventilation shutter)
2CV6, heat exchanger, left + right (1 pair). Good reproduction made of stainless steel. The heat
exchangers are like the original, and also have the foam on the flaps. But the 2CV with stainless steel heat exchanger sounds slightly different (louder, more metallic). Attention: The heat exchangers fit only on the Citroen 2CV6 (Dyane, Mehari, AK, AMI8), until 1990, not suitable for 2CV4.
2CV6, heat exchanger, left + right (1 pair). Good replica. The heat exchangers are like the
original, and also have the foam on the flaps. The heat exchangers are black powder coated. Attention: The heat exchangers fit only on the Citroen 2CV6 (Dyane, Mehari, AK, AMI8), until 1990. Not suitable for 2CV4.
2CV6, heat exchanger (heat exchanger), exhaust pipe on the left in the heat exchanger. As
substitute for through-rusted pipes. Caution, it is only the pipe, not the kompette heat exchanger.
2CV6, heat exchanger, exhaust pipe on the right in the heat exchanger. As substitute for
through-rusted pipes. Caution, it is only the pipe, not the kompette heat exchanger.
Hot air (Defroster) nozzle seal, in the firewall (for the warm air funnel, above at the
windshield). Suitable for Citroen 2CV. Or. No. AZ564-74B.
Defroster nozzle rubber stop. Suitable for Citroen 2CV. This small rubber is attached to the
defroster nozzle and prevents vibration noises. Suitable for Citroen 2CV. The defroster nozzle is mounted behind the dashboard trim and directs the warm air from the heater to the windscreen.
Heating air fan for the installation into the heating hose of Citroen 2CV. The hose is cut through
and mounted then the fan between the heating hose ends. Optically almost invisibly. The mounting material is provided. The fan has the following dimensions: 80mm diameter, construction length 50mm.
Heating air fan in snail form. By the design a larger air orifice is possible. For conversion in
Citroen 2CV. Without built-in set. The suitable built-in set has the number 14505.
Heating hose 2CV top, RHD, between distributor warm air and upper nozzle, for right hand drive 2CV
80mm inside diameter, 15mm foam material. Overall length about 1000mm.
Heating hose lined (with foam on the inside). Suitable for Citroen 2CV6, 2CV4 + AMI6. Own
reproduction. With aluminium core, making it much more durable! 500 mm long, 90 mm outer diameter, 15 mm foam.
Heating hose above, for Citroen 2CV6+4. length about 225mm. This hose was mounted between the warm
air distributor in the engine compartment and the air duct at the windshield. The hose is isolate with foam material.
Heating hose set for Citroen 2CV6. Consisting of: 2x heating hose of the heat exchanger into the
interior, 1x heating hose above, between distributor warm air and upper nozzle, 2x exhaust air hose made of rubber! Complete set!
Heating hose set for Citroen 2CV6. Consisting of: 2x heating hose of the heat exchanger into the
interior, 1x heating hose above, between distributor warm air and upper nozzle, 2x exhaust air hose! Complete set!
Heater adjustment lever with fixture. Suitable for Citroen 2CV, HY, Mehari. Reproduction out of
f painted sheet metal. Or. No. 5403748
Heater cable sheet metal holder, securement of the heater cable on the heat exchanger. This sheet
metal holder is for both heater cables. Suitable for Citroen 2CV.
Heater cable sheet metal holder, securement of the heater cable on the heat exchanger. This sheet
metal holder is for one heater cable. Suitable for Citroen 2CV.
Heater cable short, suitable for Citroen 2CV, for all years of construction. Installed one between
the heating exchangers in the engine compartment. Depending upon year of construction it can be possible that the cable must be cut.
Heater cable long, for Citroen 2CV6. Mounted at the heater adjustment lever in the interior to the
heating exchanger. Installed one starting from 04/1972. Bowden cable about 1480mm long. Casing about 1250mm. The heater cable is individually shortenable.
Heater cable tension force clamp (wide) on the heat exchangers, for Citroen 2CV. With this tension
force clamp the two heater cables are adjusted. Significant after production from the European Union. Or.Nr. AZU 644-101
Heater cable tension force clamp (wide) on the heat exchangers, for Citroen 2CV. With this tension
force clamp the two heater cables are adjusted. Or.Nr. AZU 644-101
Cable tie made of rubber, for 2CV/DS, like the original. Length: 270mm, breadth:12mm. Made in
Germany. Now manufactured from improved material (NBR/SBR fabric rubber)
Cable tie made of rubber, for 2CV/DS, like the original. Length: 320mm, breadth: 12mm. Made in
Germany. Now manufactured from improved material (NBR/SBR fabric rubber)
Clamp for attaching the heating cable to the heat exchanger. The clips are at the end of the heater
cable and are clipped onto the heat exchanger. Suitable for Citroen 2CV, old version. On a 2CV6, the cables on the heater exchanger have been screwed on since 1977.
Clip for the securement heater cable at the heat exchanger. Suitable for Citroen 2CV, old version
With a 2CV6, since 1977, the cable are screwed on to the heat exchanger.
79 Articles | Page 1 of 2
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
