Tie rods slide ring squarely (1 oversize), mounts in the steering gear. Suitable for Citroen 2CV
Reproduction from a brass alloy. Oversize: about 8 x 13 x 21mm.
for Citroën 2CV 2CV6
2768 Articles | Page 48 of 56
Tie rods slide ring squarely, mounts in the steering gear. Suitable for Citroen 2CV. Reproduction
from a brass alloy. Standard measurement about 8x13x20.
Tie rod locking plate, suitable for Citroen 2CV. For tie rod lever with stepped attachment
Installed from year of construction 1963. Or. No.: AM41389. Like the original plates, our locking plates are slightly bent up at the ends. This makes them easier to fold over (securing the screws)
Split pin small, for the tie rod end nut + radius arm bearing. Suitable for Citroen 2CV
Measurement: 2 x 20mm
Tie rod end wrench (630-16/2), for the nut in the tie rod end. Suitable for Citroen 2CV. Note: this
tool do not fit for tie rod end with strengthened nuts.
Tie rod end on the left (only the case, without spring and bearing pans). Suitable for Citroen 2CV
Made one in Germany. Or.Nr.: A44398B. Thread: M14x1,25 left-hand thread
Tie rod end on the right (only the case, without spring and bearing pans). Suitable for Citroen
2CV. Made one in Germany. Or.Nr.: A44398C. Thread: M14x1,25 left-hand thread
Tie rod end repair set on the left. Inclusive bearing pan, pressure spring, locking nut, collar
safety sheet. Suitable for Citroen 2CV. Thread: M14x1,25 left-hand thread.
Tie rod end repair set on the right. Inclusive bearing pan, pressure spring, locking nut, collar
safety sheet. Suitable for Citroen 2CV. Thread: M14x1,25 left-hand thread.
Tie rod end locking nut. Suitable for Citroen 2CV. The nut is additionally equipped with a
lubrication nipple. A real improvement!
Tie rod end, 2 x seat bowl + 1 x pressure spring + 1 x crown nut. Complete repair set, in order to
repair the tie rod end inside. High quality. Suitable for all Citroen 2CV, AK, Dyane, AMI.
Spring in the tie rod end. Suitable for Citroen 2CV. Per side 1x spring is required.
- Suitable for this article
Tie rod end collar "Made in European Union", suitable for Citroen 2CV, Mehari, Dyane, AMI. This
collar is produced in Europe for "Der Franzose". The collar is very flexible and can be mounted over the complete tie rod end, without it tears. Better than original!
Dust cap from rubber, for the vent screw at brake calipers and wheel brake cylinders. Universal
suitable for Citroen, Peugeot, Renault.
Plug protection against humidity, made of rubber to wrap around the plug connections, suitable for
2CV, only on the bracket assembly for the headlamps.
Stud bolt M7 on top of the gearbox (gearbox cover). The stud bolt secures the brake line to the
gearbox cover. Suitable for Citroen 2CV6, Dyane 6, Mehari, ACDY. Thread: M7. Total length: 50 mm. Thread length above the 11 mm head: 13 mm. Thread length below the head: 30 mm.
Stud bolt M8 x 35. For the securement of the carburetor on the intake manifold. Suitable for
Citroen 2CV6 + 2CV4. (round + oval carburetor). Or. No. 26 161 509
Stop sleeve for the clutch cable (2CV to year of construction 1967, with diagonal clutch release
fork lever) and for the hand brake cables drum brake. Or. No. A454-76.
Shock absorber (2 fittings) in the rear, for Citroen 2CV + Dyane. For 12mm shock absorber
securement. Manufacturer "Record France". Price is for 2 fittings. Mounting: Synthetic cap to the wheel! The shock absorbers please 5x push through, before they are mounted. Air in the shock absorber is removed! These shock absorbers are oil pressure shock absorbers are soft. Just as the 2CV was originally delivered.
Shock absorber (2 fittings) in front, for Citroen 2CV + Dyane. For 12mm shock absorber securement
Manufacturer "Record France". Price is for 2 fittings. Mounting: Synthetic cap to the wheel! The shock absorbers please 5x push through, before they are mounted. Air in the shock absorber is removed! Length compressed: 340mm. Extended: 500mm. These shock absorbers are oil pressure shock absorbers are soft. Just as the 2CV was originally delivered.
Gas pressure shock absorber (2 fittings) in the rear, for Citroen 2CV. For 12mm shock absorber
securement. Manufacturer "Record France". The gas pressure shock absorbers are a bit firmer (but not hard), but have a more sensitive response. Price is for 2 fittings. Mounting: Synthetic cap to the wheel! The shock absorbers please 5x push through, before they are mounted. We only use gas pressure dampers on our 2CVs. So that's our recommendation!
Gas pressure shock absorber (2 fittings) in front, for Citroen 2CV. For 12mm shock absorber
securement. Manufacturer "Record France". The gas pressure shock absorbers are a bit firmer (but not hard), but have a more sensitive response. Price is for 2 fittings. Mounting: Synthetic cap to the wheel! The shock absorbers please 5x push through, before they are mounted. Length compressed: 340mm. Extended: 500mm. We only use gas pressure dampers on our 2CVs. So that's our recommendation!
Shock absorber rear, suitable for Citroen 2CV (per piece). 12mm securement eye. Manufacturer Boge
Sachs! The Boge Sachs shock absorber is very soft!
Shock absorber in front, suitable for Citroen 2CV (per piece). 12mm securement eye. Manufacturer
Boge Sachs! The Boge Sachs shock absorber is very soft!
2768 Articles | Page 48 of 56
Select your Citroen 
Please select your Peugeot 
Please select your Citroen Renault 
